Bedienungsanleitung Quadra-Fire Castile - Pellet - Insert (Seite 28 von 40) (Englisch)

815528

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

28 02/237022-802K

2. Convection Blower: The convection blower is mounted

at the bottom rear of the appliance. There are 2 impellers,

one on each side of the motor. The convection blower

pushes air through the heat exchange system into the

room.

3. Exhaust Blower: The exhaust blower is mounted on the

right side of the appliance behind the right side panel.

The exhaust blower is designed to pull the exhaust from

the appliance and push it out through the venting system.

4. Feed System: The feed system is located behind the

rebox and can be removed as an entire assembly. The

assembly includes the feed motor, mounting bracket,

bearing and feed spring (auger). The hollow feed spring

(auger) pulls pellets up the feed tube from the hopper

area and drops them down the feed chute into the re

pot at a set rate. The feed motor starts and stops every 7

seconds.

5. Fire pot: The re pot is made of high quality ductile iron

and has a cleaning pull-out rod. The oor of the re pot

opens for cleaning when you pull out the rod. Be sure that

the oor returns to a completely closed position or your

appliance will not operate properly.

6. Fuse: The fuse is located on the side of the junction box

near the red call light. The fuse will blow should a short

occur and shut off power to the appliance.

7. Heat Exchangers: The heat exchangers transfer heat

from the exhaust system into convection air. There are 2

clean out rods located under the heat exchangers.

A. Component Functions

1. Control Box

a. The control box is located on lower right side of

appliance, on top of the junction box.

b. There is a light located inside of the control box. The

internal light will turn green when the appliance has

reached a temperature of 200°F (93°C) in the re pot.

and will turn red when it reaches 600°F (315°C).

c. There is also an internal blue light located in the

upper left corner of the control box. When you plug

in the appliance the blue light will automatically start

blinking 6 blinks every 10 seconds for 60 seconds

(depending upon setting) and then will stop.

NOTE: Do NOT open the control box. This will void the

warranty. If you need to plug in or remove the control box

you must rst unplug the appliance.

8. Heat Output Switch: The heat output switch is located

on the lower right side of rebox, behind the front access

door and above the reset button. The function of the heat

output switch is to regulate the burn rates; low, medium

and high settings.

9. Hopper Switch: The hopper switch is located in the

upper right hand corner, outside of the hopper. This

switch is designed to shut down the feed motor whenever

the hopper lid is opened.

10. Igniter: The igniter is mounted on the base of the re pot.

Combustion air travels over the red hot igniter creating

super heated air that ignites the pellets.

11. Junction Box And Wiring Harness: The junction box is

located on the lower right side of the appliance, behind

the left front access door. The junction box and wiring

harness are replaced as one component.

12. Power Supply: The power outlet is located on the lower

right side of the appliance on the front of the junction box.

Check the wall receptacle for 120 volt, 60 Hz (standard

current). Make sure the outlet is grounded and has the

correct polarity. A good surge protector is recommended.

When operating with a generator you need a least 600

watts of power, or with an inverter at least 800 watts of

power available for the appliance during the start cycle.

13. Red Call Light: The red call light is on the top of the

junction box by the fuse. The function of the red call light

is to indicate that the thermostat is calling for heat.

14. Reset Button: The reset button is located on the lower

right side of rebox in behind the access door and below

the heat output control switch. The function of the switch

is to momentarily open the thermostat circuit, which

restarts the system.

15. Thermocouple: The thermocouple is located on

top of the re pot inside the thermocouple cover

(ceramic protection tube). The thermocouple sends a

millivolt signal to the control box indicating the preset

temperatures of the green and red lights have been

obtained.

16. Thermostat: The appliance is designed to run on a

5 volt DC thermostat. The heat anticipator, if present,

should be set on the lowest setting available.

When describing the location of a

component, it is always AS YOU FACE

THE FRONT OF THE APPLIANCE.

6 6 reference Materials

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Castile - Pellet - Insert Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Castile - Pellet - Insert

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info