Bedienungsanleitung Quadra-Fire Castile - Pellet (Seite 25 von 40) (Englisch)

815522

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

25 12/237021-802L

A. Blowers

1. Convection Blower

PART NUMBER: 812-4900

NOTE: The convection blower must be removed before

the exhaust blower can be removed.

Side Screws,

Loosen Do Not

Remove

Side Screws,

Loosen Do Not

Remove

Remove back screws and

bend top back leaving it

attached at the bottom

Figure 25.1

Remove 6 screws

Figure 25.2

Figure 25.3

Loosen (do not remove) 2

screws on each side and lift

off blower housing

Remove left side

panel and disconnect

blower wires

Convection Blower

& Housing

5 5 Service Parts Replacement

2. Combustion Blower

PART NUMBER: 812-4400

a. Turn down thermostat, let appliance completely cool

and then unplug appliance before servicing.

b. The convection blower is located at the bottom rear

of the appliance and is housed inside a screen box.

Remove the 2 screws facing forward in the center of

the blower chamber at the very back of the appliance.

c. If an outside air kit is installed on the appliance, these

screws attach the intake air channel piece of the

outside air kit to the appliance. Remove the 2 screws

and pull backwards on the channel and it will slide

down and away from the appliance. The air channel,

collar and outside air hose will be removed as one

piece.

d. There are 2 screws on each side of the housing.

Loosen all 4 screws, but do not remove them. Lift

the blower housing up slightly and slide towards you

(Figure 25.3).

e. Remove the left side panel by loosening 2 screws

(do not remove) and pull side panel away. Unplug

the 2 black blower wires by disconnecting the spade

connectors.

f. To remove blower from the housing, remove 2 screws

in the front of the housing and very carefully bend the

2 housing sides out and bend the back of the housing

away from the blower. This allows for room to access

the back 2 screws and nuts (4 total) that is securing

the blower to the housing.

g. Remove blower and replace with new blower.

h. Re-install in reverse order.

a. Turn down thermostat, let appliance completely cool

and then unplug appliance before servicing.

b. Remove both side curtains by loosening 2 screws (do

not remove) and pull side panels away.

c. Remove 4 screws from the back screen and pivot

the top of the screen toward you leaving the bottom

attached to appliance (Figure 25.1).

d. Remove 2 screws to remove the thermostat block

and disconnect the 2 yellow wires.

e. Remove the 2 screws from the power inlet and rotate

it through the hole and out of the screen, leaving the

wires attached.

f. Disconnect the vacuum hose and both wires (orange

and red) from the vacuum switch attached to the rear

screen.

g. Remove both wires from exhaust blower (blue and

double white).

h. Remove 6 screws using a athead screwdriver or a

1/4” nut-driver. Retain screws for use on replacement

blower (Figure 25.2).

i. Remove exhaust blower and gasket.

j. Install new gasket and blower. Discard blower housing

if not needed.

k. Re-install in reverse order.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Castile - Pellet Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Castile - Pellet

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info