Bedienungsanleitung Quadra-Fire Castile - Pellet (Seite 29 von 40) (Englisch)

815522

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

29 12/237021-802L

When describing the location of a

component, it is always AS YOU FACE

THE FRONT OF THE APPLIANCE.

A. Component Functions

1. Control Box

a. The control box is located on upper right side of

appliance, behind the right side panel and above the

vacuum switch.

b. There is a light located inside of the control box. The

internal light will turn green when the appliance has

reached a temperature of 200°F (93°C) in the re pot

and will turn red when it reaches 600°F (315°C).

c. There is also an internal blue light located in the

upper left corner of the control box. When you plug

in the appliance the blue light will automatically start

blinking 6 times in a row for 60 seconds and then will

stop.

NOTE: Do NOT open the control box. This will void the

warranty. If you need to plug in or remove the control box

you must rst unplug the appliance.

6 6 Reference Materials

8. Heat Output Switch: The heat output switch is located

on the upper right rear panel. The function of the heat

output switch is to regulate the burn rates; low, medium

and high settings.

9. Hopper Switch: The hopper switch is located in the

upper right hand corner of the hopper. This switch is

designed to shut down the feed motor whenever the

hopper lid is opened.

10. Igniter: The igniter is mounted on the base of the re

pot. Combustion air travels over the red hot igniter

creating super heated air that ignites the pellets.

11. Junction Box And Wiring Harness: The junction box

is located on the right side of the appliance, behind the

right side panel. The junction box and wiring harness

are replaced as one component.

12. Power Supply: The power outlet is located behind

the control box on the back of the appliance, lower left

corner. Check the wall receptacle for 120 volt, 60 Hz

(standard current). Make sure the outlet is grounded

and has the correct polarity. A good surge protector is

recommended.

13. Red Call Light: The red call light is on the side of the

junction box, next to the fuse. The function of the red

call light is to indicate that the thermostat is calling for

heat.

14. Reset Button: The reset button is located on the back

of the appliance in the upper right corner below the heat

output control switch. The function of the button is to

momentarily open the thermostat circuit, which restarts

the system.

15. Thermocouple: The thermocouple is located on

top of the re pot inside the thermocouple cover

(ceramic protection tube). The thermocouple sends a

millivolt signal to the control box indicating the preset

temperatures of the green and red lights have been

obtained.

16. Thermostat: The appliance is designed to run on a 12

volt AC thermostat. The heat anticipator should be set

on the lowest setting available.

2. Convection Blower: The convection blower is mounted

at the bottom rear of the appliance. There are 2 impellers,

one on each side of the motor. The convection blower

pushes heated air through the heat exchange system

into the room.

3. Exhaust Blower: The exhaust blower is mounted on

the right side of the appliance. The exhaust blower is

designed to pull the exhaust from the appliance and

push it out through the venting system.

4. Feed System: The feed system is located on the right

side of the appliance and can be removed as an entire

assembly. The assembly includes the feed motor,

mounting bracket, bearing and feed spring (auger). The

hollow feed spring (auger) pulls pellets up the feed tube

from the hopper area and drops them down the feed

chute into the re pot.

5. Fire pot: The re pot is made of high quality ductile iron

and has a cleaning pull-out rod. The oor of the re pot

opens for cleaning when you pull out the rod. Be sure

that the oor returns to a completely closed position or

your appliance will not operate properly.

6. Fuse: The fuse is located on the front of the junction

box next to the red call light. The fuse will blow should a

short occur and shut off power to the appliance.

7. Heat Exchangers: The heat exchangers transfer hot air

from the exhaust system into convection air. Remove the

stainless steel top bafe to access the heat exchangers.

There are 2 clean out rods located under the heat

exchangers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Castile - Pellet Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Castile - Pellet

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info