Bedienungsanleitung Quadra-Fire Classic Bay 1200 - Pellet

815525

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

26 04/217027-805J

A. Blower

1. Combustion (Exhaust) Blower Replacement

PART NUMBER: 812-3381

a. Prep appliance from the blower removal:

i. Disconnect the appliance from the electrical outlet.

ii. Remove panel set and disconnect ue.

iii. Pull appliance out onto the hearth.

iv. Remove the right-side access panel, then slide out

the right-side panel of the appliance, held in place

with 2 screws, to expose the exhaust blower.

b. Remove existing blower (Figure 26.1):

i. Use the 11/32” wrench or nut driver to loosen and

remove the (6) nuts holding the motor mount plate

to the blower housing on your appliance.

ii. Remove the washer from beneath the terminal

ring on the grounding wire.

iii. Pull motor/mounting plate from blower housing.

iv. Scrape o󰀨 the old gasket material from

blower housing.

c. Install new blower:

i. The blower and blower housing is shipped as a

appliance in this kit. It is necessary to separate

them at this point.

ii. Use 11/32” wrench or nut driver to loosen and

remove the (6) nuts holding the motor mount plate

to the blower housing.

iii. Remove the washer from beneath the terminal

ring on the grounding wire.

iv. Pull motor/mounting plate from blower housing

and discard or set aside the blower housing.

v. Carefully remove gasket from new housing and

set onto the appliance blower housing.

d. Reinstall blower to blower housing:

i. Install blower on housing ensuring that wiring exits

at the 12 o’clock position. Place washer and then

grounding wire on nearest mounting plate stud.

ii. Use nuts removed in step A1 to secure blower to

housing.

iii. Reconnect wiring. Use Jumper wire if necessary.

Reconnect power supply.

e. Re-install appliance:

i. Reassemble right side panel to appliance with 2

screws previously removed.

ii. Push appliance back into the hearth.

iii. Reconnect ue and re-install panel set; plug in

appliance to electrical outlet.

Figure 26.1

Blue Wire

White Wires

Housing Bolts

Blower Mounting

Screws

5 5 Service Parts Replacement

2. Convection Blower Replacement

PART NUMBER: 812-4900

a. The blower is located at the bottom rear of the insert.

If an outside air kit is also installed, you will rst need

to remove the outside air ange by removing the 2

screws using a Phillips head screwdriver. You do not

need to remove the ex pipe from the ange.

b. Remove panel set and disconnect ue.

c. Pull appliance out onto the hearth.

d. Remove left access panel and then slide out left side

panel of appliance to expose the convection blower.

Loosen wing nut on the vacuum switch and remove

vacuum switch to allow room to remove the blower.

e. Disconnect the wires from the blower. The wires

coming from the wiring harness are purple & white

and the wires from the blower are black.

f. The blower is held in place with a magnet. A wing

nut and plate are installed at the factory for shipping

purposes only. This can be removed once the

appliance is installed. Lift up blower from the magnet

and remove.

g. Re-install in reverse order.

Shock Risk.

• Do NOT remove grounding prong

from plug.

• Plug directly into properly grounded 3

prong receptacle.

• Route cord away from appliance.

• Do NOT route cord under or in front

of appliance.

CAUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Classic Bay 1200 - Pellet - Insert Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Classic Bay 1200 - Pellet - Insert

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info