Bedienungsanleitung Quadra-Fire Classic Bay 1200 - Pellet

815525

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

29 04/217027-805J

A. Component Function

1. Control Box

a. The control box is located on right side of appliance,

behind the right side panel.

b. There is a light located inside of the control box. The

internal light will turn green when the appliance has

reached a temperature of 200°F (93°C) in the re pot

and will turn red when it reaches 600°F (315°C).

c. There is also an internal blue light located in the

upper left corner of the control box. When you plug

in the appliance the blue light will automatically start

blinking 1 blink every 10 seconds for 60 seconds and

then will stop.

NOTE: Do NOT open the control box. This will void the

warranty. If you need to plug in or remove the control box

you must rst unplug the appliance.

When describing the location of a

component, it is always AS YOU FACE

THE FRONT OF THE APPLIANCE.

6 6 Reference Materials

8. Heat Output Switch: The heat output switch is located

on the right side of rebox, behind right side panel. The

function of the heat output switch is to regulate the burn

rates; low, medium and high settings.

9. Hopper Switch: The hopper switch is located in the

upper right hand corner of the hopper. This switch is

designed to shut down the feed motor whenever the

hopper lid is opened.

10. Igniter: The igniter is mounted on the base of the re

pot. Combustion air travels over the red hot igniter

creating super heated air that ignites the pellets.

11. Junction Box And Wiring Harness: The junction box

is located on the right side of the appliance, behind the

right front access panel. The junction box and wiring

harness are replaced as one component.

12. Power Supply: The power outlet is located on the

right side of the appliance. Check the wall receptacle

for 120 volt, 60 Hz (standard current). Make sure the

outlet is grounded and has the correct polarity. A good

surge protector is recommended. When operating with

a generator you need at least 600 watts of power, or

with an inverter at least 800 watts of power, available

for the appliance during the start cycle.

13. Red Call Light: The red call light is on the right side

behind the right side panel. The function of the red call

light is to indicate that the thermostat is calling for heat.

14. Reset Button: The reset button is located on the right

side of rebox behind right side panel. The function of

the reset button is to momentarily open the thermostat

circuit, which restarts the system.

15. Thermocouple: The thermocouple is located on

top of the re pot inside the thermocouple cover

(ceramic protection tube). The thermocouple sends a

millivolt signal to the control box indicating the preset

temperatures of the green and red lights have been

obtained.

2. Convection Blower: The convection blower is mounted

at the bottom rear of the appliance. There are 2 impellers,

one on each side of the motor. The convection blower

pushes heated air through the heat exchange system

into the room.

3. Combustion (Exhaust) Blower: The combustion blower

is mounted on the left side of the appliance behind the

left side panel. It is accessible either when the insert

is pulled out onto the hearth or from both hinged side

openings. The blower is designed to pull the exhaust

from the appliance and push it out through the venting

system.

4. Feed System: The feed system is located behind the

rebox and can be removed as an entire assembly. The

assembly includes the feed motor, mounting bracket,

bearing and feed spring (auger). The hollow feed spring

(auger) pulls pellets up the feed tube from the hopper

area and drops them down the feed chute into the re

pot.

5. Fire pot: The re pot is made of high quality ductile iron

and has a cleaning pull-out rod. The oor of the re pot

opens for cleaning when you pull out the rod. Be sure

that the oor returns to a completely closed position or

your appliance will not operate properly.

6. Fuse: The fuse is located on the right side of the appliance

behind the side panel. The fuse will blow should a short

occur and shut o󰀨 power to the appliance.

7. Heat Exchangers: The heat exchangers transfer heat

from the exhaust system into convection air. There are 2

clean out rods located under the heat exchangers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Classic Bay 1200 - Pellet - Insert Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Classic Bay 1200 - Pellet - Insert

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info