Bedienungsanleitung Quadra-Fire Discovery III (Seite 18 von 32) (Englisch)

815513

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

18 02/237037-804G

4. Glass Cleaning

• Frequency: As desired

• By: Homeowner

CAUTION

• Do not use polishes with abrasives. It will scratch

plated surfaces.

CAUTION

• Do not use polishes with abrasives. It will

scratch surfaces.

5. Cleaning Plated Surfaces

• Frequency: Prior to first burn and then as desired

• By: Homeowner

Clean all the ngerprints and oils from plated surfaces

BEFORE ring the appliance for the rst time. If not

cleaned properly before lighting your rst re, the oils can

cause permanent markings on the plating.

After the plating is cured, the oils will not affect the nish

and little maintenance is required. Wipe clean as needed.

Clean glass with a non-abrasive glass cleaner. Abrasive

cleaners may scratch and cause glass to crack. If the

deposits on the glass are not very heavy, normal glass

cleaners work well. Heavier deposits may be removed by

using a damp cloth dipped in wood ashes or by using a

commercially available oven cleaner.

After using an oven cleaner, it is advisable to remove any

residue with a glass cleaner or soap and water. Oven

cleaner left on during the next ring can permanently stain

the glass and damage the nish on metal surfaces.

A portion of the combustion air entering the rebox is

deected down over the inside of the door glass. This

air ow “washes” the glass, helping to keep smoke from

adhering to its surface.

When operated at a low burn rate, less air will be owing

over the glass and the smokey, relatively cool condition of a

low re will cause the glass to become coated.

Operating the appliance with the Burn Rate Air Control and

Start-Up Air Control all the way open for 30-45 minutes

should remove the built up coating.

CAUTION

Handle glass assembly with care. Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• Do not clean glass while it is hot

6. Inspect Firebrick

• Frequency: After each ash removal

• By: Homeowner

Replace the rebrick if they become crumbly and/or if there

is a 1/4 inch (6.35mm) gap between the bricks.

The rebox is lined with rebrick, which has exceptional

insulating properties. Do not use a grate; simply build

a re on the rebox oor. Do not operate appliance

without rebrick.

1. After the coals have completely cooled, remove all old

brick and ash from unit and vacuum rebox.

2. Remove new brick set from box and lay out to the

diagram shown in the instructions that come with the

brick set or refer to the diagram on the service parts list

at the end of this manual.

3. Lay bottom bricks in unit.

4. Install rear bricks on the top of the bottom bricks. Slide

top of bricks under clip on back of rebox wall and push

bottom of bricks back.

5. Install side bricks. Slide top of brick under clips on side

of rebox and push the bottom of the brick until it is

ush with the side of the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Discovery III Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Discovery III

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info