Bedienungsanleitung Quadra-Fire Expedition II (Seite 21 von 34) (Englisch)

815519

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

21 7095-803R 12/23

5 5 Service Parts Replacement

A. Glass B. Firebrick

Service Part: SRV7095-022

Replace the rebrick if they become crumbly and/or if there

is a 1/4 inch (6.35mm) gap between the bricks.

Inspect the rebrick after each ash removal.

The rebox is lined with high quality rebrick, which has

exceptional insulating properties. There is no need to use a

grate; simply build a re on the rebox oor. Do not operate

appliance without rebrick.

1. After the coals have completely cooled, remove all old

brick and ash from appliance and vacuum rebox.

2. Remove new brick set from box and lay out to

diagram shown.

3. Lay bottom bricks in appliance.

4. Install rear bricks on the top of the bottom bricks. Slide

top of bricks under clip on back of rebox wall and push

bottom of brick back.

5. Install side bricks. Slide top of brick under clips on side

of rebox and push the bottom of the brick until it is ush

with the side of the appliance.

NOTE: Replace with 5mm ceramic glass only.

Service Part: SRV7095-054

1. Ensure that the re is out and the appliance is cool to the

touch.

2. Protect a table or counter top with padding or towels.

Protect your hands and wear gloves to prevent injury.

3. Remove the door with the broken glass by lifting the door

up and o󰀨 of the hinges.

4. Lay door face down on a table or counter making sure

the handle hangs over the edge so the door lays at, on

a soft surface.

5. Remove the screws from each glass retainer and remove

the glass. (If screws are di󰀩cult to remove, soak with

penetrating oil rst).

6. Center the glass with edges evenly overlapping the

opening in the door, (i.e. same space top and bottom,

left and right sides).

7. Replace the glass retainers. Be careful not to cross

thread the screws.

8. Tighten each retainer just a few turns until each is

secured. Check again for centering of glass in door

frame. Continue to tighten each retainer alternately, a

few turns at a time, until the glass is secure.

4 45

1 1 1 1 1

Figure 21.1

1.31

5.81

Figure 21.2

Placement Dimensions Qty Required

19” x 4.5” x 1.25” 13

24.5” x 4.5” x 1.25” 1

35.75” x 4.5” x 1.25” 1

49” x 3” x 1.25” 2

57” x 3” x 1.25” 1

69” x 4.5” x 1.25” w/Angle 2

Table 21.1

NOTE: DO NOT OVER TIGHTEN RETAINERS - can

cause glass to break.

9. Replace the door on the appliance.

Quadra-Fire appliances are equipped with ceramic super

heat-resistant glass, which can only be broken by impact

or misuse.

Injury Risk.

• Use only glass specied in manual.

• DO NOT REPLACE with any other material.

WARNING

Handle glass assembly with care.

When cleaning glass:

Glass

Assembly

CAUTION

• Avoid striking, scratching or slamming glass.

• Do NOT clean glass when hot.

• Do NOT use abrasive cleaners.

• Use a hard water deposit glass cleaner on white lm.

• Use commercial oven cleaner on heavier deposits.

• Remove all residue of oven cleaner or will

permanently stain glass on next ring.

Refer to maintenance instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Expedition II Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Expedition II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info