Bedienungsanleitung Quadral AURUM 9 PASSIV (Seite 5 von 23) (Deutsch, Englisch, Französisch, Spanisch)

698705

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Subwoofer

Low Level connection

Surround-amplifier

Left

right

During Bi-wiring / Bi-amping operation of the AURUM loudspeaker, both screw terminals for the woofer (LO)

are below and for the midrange speakers and tweeters (Hl) are above on the connection plate.

Only the largest models of the AURUM 9 series are fitted with an extended connector panel by means of

which these connections are arranged horizontally and the various operating modes apply analogously with

the assignment of (Hl) and (LO).

Make sure you use the correct polarities in these modes and that you remove the jumpers on the speaker

terminal to avoid damaging your amplifier.

OPERATION WITH A SURROUND AMPLIFIER

Once you have positioned and connected your speakers as shown in the illustration, you should perform the

necessary settings in the bass management system of your surround amplifier.

Make sure you read the user manual supplied by your amplifier’s manufacturer before doing this.

Since bass management primarily depends on the loudspeaker configuration, we give only typical settings

below.

a) Small and very small satellite speakers must be operated in “small” mode.

Perform the setting on your amplifier as follows:

Front: small Centre: small

Rear: small Subwoofer: yes

b) There is no definitive formula for the settings for compact speakers. In this case, the suitable mode may be

“large” or “small”. This depends on the volume level you prefer or the sound effect you wish to obtain (refer

to the section “Caution, clipping!”). The settings on your amplifier can optionally be configured as follows:

Front: large/small Centre: large/small

Rear: large/small Subwoofer: yes

c) Floorstanding speakers or large bookshelf speakers that are suitable for powerful bass reproduction

should be operated in “large” mode.

Perform the setting on the amplifier as follows:

Front: large Centre: large

Rear: large Subwoofer: yes/no

Subwoofer

If your surround amplifier has a “line subwoofer” output, you can make use of this by using the Y cable supplied

with the subwoofer (see illustration page 8). In this case, you connect the front speakers directly to the front

speaker terminals of your amplifier. Refer to the connection diagram for wiring your surround system.

Refer to the user manual of the active subwoofer for the necessary settings on your subwoofer!

TIPS FOR BETTER ACOUSTICS

1. The AURUM stand-mounted loudspeakers are fitted with a holder for spikes in order to achieve better

acoustic decoupling of loudspeaker from the floor. Use of spikes can be advantageous dependent on the

nature of the living room and the floor.

AURUM spikes can be obtained separately as an accessory from your dealer.

2. In order to achieve better acoustic decoupling from the mounting surface for shelf or centre speakers, lay

each of these loudspeakers on 4 self-adhesive felt washers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadral AURUM 9 PASSIV Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info