Bedienungsanleitung Quadral Subwoofer (Seite 4 von 21) (Deutsch, Englisch, Französisch, Spanisch)

698713

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

ENGLISH

Connection variant no. 2

(Subwoofer in a preamp/output amp combination)

If your system consists of a preamp/power amp combination you can, connect the subwoofer

to the preamp’s output by means of a cinch cable. To do this, use the cinch sockets marked

„LOW LEVEL IN/LINE“. Also using a cinch cable, connect up your output amp to the subwoof-

er at the cinch socket „LOW LEVEL OUT“. If your preamp has 2 pairs of output sockets you

can leave the direct connection between preamp and output amp as it is and simply connect

the subwoofer to the preamp’s second cinch output; there is then no need for the subwoofer

to be connected to the power amp. In these case there is no need to use loudspeaker cables

for the connections. Put your subwoofer into operation as described under „Starting up“.

Connection variant no. 3

(Subwoofer in a surround system)

If your surround amp or receiver has a subwoofer line output (Sub Pre-Out), you can use this

by connecting the subwoofer to this socket by means of cinch cable (Connection variant no.

4a or 4b). If your surround amp does not have an output of this type you will have to connect

up the subwoofer as described under „Connection variant no. 1“.

Having connected up your subwoofer at the subwoofer line output of your digital surround

sound amplifier, you must now configure the amplifier's bass management as follows:

Subwoofer: yes

Front, center, rear: large /small (depending on size)

In these case there is no need to use loudspeaker cables for the connections. Put your sub-

woofer into operation as described under „Starting up“.

Connecting up

Please connect the device using the network cable supplied to the mains socket shown below.

Before connecting up the subwoofer to your hi-fi or surround system, make sure that the unit

and all system components are switched off, i.e. the pilot lights should all be off.

Connection variant no. 1

(Additional woofer for an existing hi-fi system)

Connect the subwoofer to your amplifier at the „B“ loudspeaker outputs. The connections of

the existing speakers remain unchanged. Having connected the subwoofer, you must then

activate the „B“ loudspeaker outputs; your amplifier’s operating manual will tell you how to

do this. Put your subwoofer into operation as described under „Starting up“.

This operating mode can only be used if you can activate the speaker outputs A & B on your

amplifier simultaneously. Please consult your amplifier's operating manual accordingly.

Connection variant no. 1

(Differences of models cause a different position of the operating elements.)

Output

Sub Pre-Out

+ RIGHT -

- LEFT +

- + - +

+ RIGHT -

- LEFT +

VERSTÄRKER

Amplifier

Pre-Amplifier

Surround-Amplifier

LoudspeakerLoudspeaker

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadral Subwoofer Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info