Bedienungsanleitung Quantum Blast (Seite 18 von 24) (Englisch)

722003

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

BLAST/REV D/OCTOBER 2002

Quantum Blast

CARE AND MAINTENANCE

PREVENTIVE MAINTENANCE

Like any motorised vehicle, your Blast requires simple preventive maintenance that can extend its service life. You can

perform some of these checks. But other checks require assistance from an authorised Pride provider. Preventive mainte-

nance is very important. If you follow the preventive maintenance guidelines in this section as scheduled, you can help ensure

that your Blast gives you years of trouble-free operation. If you have any doubt as to your Blast's care or operation, contact

your authorised Pride provider.

GENERAL GUIDELINES

l Avoid knocking or bumping the controller, especially the joystick.

l Keep the controller clean.

l Check all controller connectors on the utility tray to ensure that they are all tight and secured properly.

l When the battery condition meter is completely lit, the batteries are fully charged and the controller and the

electrical system are OK.

l If one red bar on the battery condition meter is blinking slowly, the batteries are low and need to be charged, but

the controller and the electrical system are OK.

l If the battery condition meter is blinking rapidly, the controller has detected a fault in either its own circuits or in

your Blast's circuits. Refer to ìTrouble Codesî for more information.

l Make sure the drive tyres are inflated to 30-35 psi.

WARNING! Overinflating tyres can cause them to explode and can result in personal injury.

WARNING! Do not use a high pressure hose to inflate your tyres.

l Use a rubber conditioner on the tyre sidewalls to help preserve them.

WARNING! Never use a rubber conditioner on the tread area of the tyres; doing so may make the tyres slippery

and may cause your Blast to skid.

l The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to the

shroud to help it retain its high-gloss appearance.

l Check all electrical connections. Make sure they are tight and are not corroded.

WHEELS AND SUSPENSION

According to personal needs and lifestyle, you may wish to adjust the

height of the anti-tips. By raising the anti-tip wheels, ground clearance

increases, as does your Blast's ability to "wheelie" for obstacle climb-

ing. Lowering the anti-tip wheels decreases the ground clearance, as

well as limits rearward pitching, increasing stability.

To adjust anti-tip wheels:

1. Remove the anti-tip axle bolt and nylon spacers using two, 1.27

cm ( in.) spanners. See figure 13.

2. Relocate the anti-tip wheel to one of the four adjustment holes, as

desired.

3. Replace the wheel, placing the nylon washers on each side of the

wheel, then replacing the axle bolt through the center.

4. Tighten the axle bolt and nut so that the wheel spins freely but does

not wobble side-to-side.

5. Repeat the process on the other anti-tip.

Fig. 13. Anti-tip Wheels

ANTI-TIP WHEELS

ANTI-TIP AXLE BOLT

ADJUSTMENT HOLE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Blast Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info