Bedienungsanleitung Quantum Jazzy 1450 (Seite 13 von 28) (Englisch)

721969

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

COMFORT ADJUSTMENTS

Seat Position

You can move the seat forward or rearward by changing the

extrusion mounting position.

To change the position:

1. Turn off the power to the controller.

2. Make sure the power chair is in drive mode.

3. Unplug the controller connector(s) from the power base.

4. Remove the seat from the power base.

5. Remove both extrusions from the bottom of the seat.

6. Reposition the extrusions on a different set of mounting

holes. You must move both extrusions the same number

of holes either forward or backwards. See ﬁgure 10.

7. Fasten the extrusions back onto the bottom of the seat.

8. Reinstall the seat.

9. Reconnect the controller to the power base.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can

adjust the seatback angle with the seatback release lever.

The lever is located on the right side of the seat base.

To adjust the recline angle:

1. Pull up on the seatback release lever.

2. Lean forward or backward to the desired position.

3. Release the lever.

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seatback,

you can adjust it to four (4) different angles: 90°, 102°, 105°,

or 107°.

To adjust the seatback angle:

1. Remove the adjusting screws from each seat hinge.

2. Set the seatback at the desired angle.

3. Reinstall the adjusting screws to each seat hinge and

tighten.

Armrest Width Adjustment

You can change each armrest’s width independently of

the other.

NOTE: Changing the armrest width may increase the

overall width of your power chair.

To change the armrest width:

1. Locate the two armrest knobs on each side of the

armrest receiver bracket. See ﬁgure 11.

2. Loosen the knobs.

3. Slide the armrests in or out to the desired width.

4. Tighten the knobs.

Armrest Angle Adjustment

To change the armrest angle:

1. Lift the armrest straight up so that it is perpendicular to

the ﬂoor. See ﬁgure 11.

2. Loosen the jam nut.

Figure 11. Seatback/Armrest Adjustment

Jam Nut

Armrest Angle

Adjusting Screws

Armrest Height

Adjusting Screws

Armrest Knob

Controller

Bracket

Setscrew

3. Turn the adjusting screw to raise or lower the front of the

armrest.

4. Tighten the jam nut to lock the adjusting screw into place.

Armrest Height Adjustment

To change the armrest height:

1. Loosen the two setscrews located on the armrest

receiver. See ﬁgure 11.

2. Raise or lower the armrest to the desired height.

3. Tighten the setscrews to secure the armrest.

Controller Position

You can move the controller in toward or out away from the

armrest, or change the position of the controller for either

left-hand or right-hand use.

Do not place the controller harness so that it can be

pinched in the seat frame or the power base frame.

To extend the controller:

1. Flip up the armrest so it is perpendicular to the ﬂoor.

2. Loosen the setscrew on the controller bracket. See

ﬁgure 11.

3. Slide the controller into or out of the armrest to the

desired position.

4. Tighten the setscrew to secure the controller.

WARNING!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Jazzy 1450 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quantum Jazzy 1450

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info