Bedienungsanleitung Quantum Q4 (Seite 17 von 28) (Englisch)

721960

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Make sure the positioning belt is properly secured to the

power chair and is adjusted for operator comfort before

each use.

Inspect the positioning belt for loose parts or damage,

including tears, worn spots, bent hardware, damaged

latch mechanisms, dirt or debris, before each use of

the power chair. If you discover a problem, contact your

Quantum Rehab Provider for maintenance and repair.

Positioning Belt

Your power chair may be equipped with a positioning belt that

can be adjusted for operator comfort. See ﬁgure 16 or 17.

The positioning belt is designed to support the operator so

that he/she does not slide down or forward in the seat. The

positioning belt is not designed for use as a restraining device.

The positioning belt is not designed for use as a seat belt

in a motor vehicle. Anyone traveling in a vehicle should

be properly belted into seats approved by the vehicle

manufacturer. Your power chair is not suitable for use as

a seat in any vehicle with the following exception: The

vehicle must be equipped with a Wheelchair Tie-down

and Occupant Restraint System (WTORS) that has been

installed in accordance with the tie-down manufacturer's

instructions, and is compliant with ANSI/RESNA WC/Vol.

4, Section 18/ISO 10542 standards, and the power chair

must have a transit securement system conforming

to ANSI/RESNA WC/Vol. 4, Section 19/ISO 7176-19

standards. It is essential to use a complete WTORS to

secure the power chair to the vehicle and to provide

the power chair occupant with a properly designed

and tested safety restraint system. A restraint system

with both pelvic and upper-torso belts must be used

to protect the power chair occupant and minimize the

likelihood of injury caused by contact with the vehicle

during a crash or sudden braking.

The positioning belt should be secured at all times.

Never allow the positioning belt to hang or drag on the

ﬂoor as it may become entangled.

To install the positioning belt:

1. Remove the rearmost screw that holds the seat hinge to

the seat base on both the left and right seat hinges.

2. Insert the screw through the supplied washer, through

the positioning belt and into the seat base for each side

of the power chair seat.

3. Tighten both screws.

NOTE: If your power chair is equipped with an optional

seating system, please refer to the user manual provided

with the seat for instructions on positioning belt

installation or contact your Quantum Rehab Provider.

To adjust the positioning belt for operator comfort:

1. Once seated, insert the metal tab on one side of the belt

into the plastic housing on the opposite side until you

hear a click.

2. Pull the excess strap attached to the metal tab until it is

secure, but not so tight as to cause discomfort.

To release the positioning belt:

1. Press the push button mechanism on the plastic housing.

COMFORT ADJUSTMENTS

MANDATORY!

WARNING!

Figure 16. Positioning Belt Installation and Adjustment–

Conﬁguration A

Figure 17. Positioning Belt Installation and Adjustment–

Conﬁguration B

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Q4 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quantum Q4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info