Bedienungsanleitung Quantum Q6 Edge 2.0 (Seite 14 von 28) (Englisch)

721962

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Comfort Adjustments

After becoming familiar with your power chair’s operation,

you may ﬁnd the need to make some adjustments to increase

your comfort, such as seat height and angle, armrest width,

angle and height, and controller position.

NOTE: If your power chair is equipped with a Synergy

Seat or TRU-Balance 3 Power Positioning System, refer

to the seat adjustment information contained in separate

manuals. If your power chair is equipped with a contoured

seating system, refer to the following information.

The center of gravity of your power chair was factory set

to a position that meets the needs of the demographic

majority of users. Your Quantum Rehab Provider has

evaluated your power chair and made any necessary

adjustments to suit your speciﬁc requirements. Do not

change your seating conﬁguration without ﬁrst contacting

Quantum Rehab or your Quantum Rehab Provider.

Some power chair components are heavy. You may

need assistance to lift or carry them. Please refer to

the speciﬁcations table for speciﬁc component weights

before you disassemble the power chair.

Remove the occupant from the power chair before

making any adjustments.

You may need the following to make comfort adjustments:

 metric/standard socket set and ratchet

 adjustable wrench

 metric/standard hex key set

 thread lock

Seat Height and Seat Angle Adjustment

If your power chair is not equipped with a transit securement

system, you can change the seat height to one of three

positions by raising the front and rear trapeze bars. If you

raise or lower only one trapeze bar (front or rear), you can

also change the seat base angle (dump).

If your power chair is equipped with a transit securement

system and any adjustment to the seat height or seat

angle is necessary, contact your Quantum Rehab

Provider. These comfort adjustment can only be made

by a Quantum Rehab Provider.

To change the seat height:

1. Turn off the power to the controller.

2. Make sure the power chair is in drive mode.

3. Unplug the controller connector(s) from the power base.

See ﬁgure 1.

4. Flip up the seat latch safety. See ﬁgure 6.

5. Squeeze the seat latch and release the seat from the

front trapeze bar.

6. Slide the seat forward and remove it from the power base.

Figure 14. Seat Height/Angle Adjustment

7. Remove the hardware that attaches the trapeze bars to

the seat interface weldments. See ﬁgure 14.

8. Move the trapeze bars up or down to the desired height.

NOTE: Change the seat dump by raising or lowering

only one trapeze bar (front or rear).

9. Reinstall the hardware.

10. Reinstall the seat.

11. Reconnect the controller to the power base.

MANDATORY!

WARNING!

Figure 15. Seat Position Adjustment

COMFORT ADJUSTMENTS

Seat Mounting Holes

Trapeze Bars

Hardware

Seat Interface

Weldment

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Q6 Edge 2.0 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quantum Q6 Edge 2.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info