Bedienungsanleitung Quantum Q6 Edge 2.0 (Seite 17 von 28) (Englisch)

721962

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

COMFORT ADJUSTMENTS

NOTE: For more information on operating the power

elevating seat through the controller, contact your

Quantum Rehab Provider.

The power elevating seat option is intended for use on

a level surface only. Never raise the seat from its lowest

position on an inclined surface. Failure to heed this

warning can result in the power chair tipping over.

Never raise the seat from its lowest position when

operating your power chair on bumpy or uneven

surfaces. Failure to heed this warning can result in the

power chair tipping over.

Never raise the power elevating seat while your power

chair is in the freewheel mode.

Always fasten the positioning belt when operating the

power elevating seat.

NOTE: The power elevating seat option is equipped with

a system that reduces the speed of the power chair to

one quarter when the seat is elevated. Always check to

be sure this system is operating properly before using

your power chair.

To adjust the positioning belt for operator comfort:

1. Once seated, insert the metal tab on one side of the belt

into the plastic housing on the opposite side until you

hear a click. See ﬁgure 19.

2. Pull the excess strap attached to the metal tab until it is

secure, but not so tight as to cause discomfort.

To release the positioning belt:

1. Press the push button mechanism on the plastic housing.

Make sure the positioning belt is properly secured to the

power chair and is adjusted for operator comfort before

each use.

Inspect the positioning belt for loose parts or damage,

including tears, worn spots, bent hardware, damaged

latch mechanisms, dirt or debris, before each use of

the power chair. If you discover a problem, contact your

Quantum Rehab Provider for maintenance and repair.

Figure 19. Positioning Belt Adjustment

MANDATORY!

Positioning Belt

Your power chair may be equipped with a positioning belt

that can be adjusted for operator comfort. See ﬁgure 19.

The positioning belt is designed to support the operator

so that he/she does not slide down or forward in the seat.

The positioning belt is not designed for use as a restraining

device.

The positioning belt is not designed for use as a seat

belt in a motor vehicle. Nor is your power chair suitable

for use as a seat in any vehicle. Anyone traveling in a

vehicle should be properly belted into seats approved

by the vehicle manufacturer.

The positioning belt should be secured at all times.

Never allow the positioning belt to hang or drag on the

ﬂoor as it may become entangled.

To install the positioning belt:

1. Remove the rearmost screw that holds the seat hinge to

the seat base on both the left and right seat hinges.

2. Insert the screw through the supplied washer, through

the positioning belt and into the seat base for each side

of the power chair seat.

3. Tighten both screws.

WARNING!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Q6 Edge 2.0 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quantum Q6 Edge 2.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info