Bedienungsanleitung Quantum Q6 Edge 2.0 (Seite 25 von 28) (Englisch)

721962

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

CARE AND MAINTENANCE

Battery Replacement

A battery wiring diagram is printed on a decal located on

the front cover. See the speciﬁcation table for correct battery

speciﬁcations.

Battery posts, terminals, and related accessories

contain lead and lead compounds. Wear goggles and

gloves when handling batteries and wash hands after

handling.

The batteries in your power chair should only be

serviced or replaced by a Quantum Rehab Provider or a

qualiﬁed technician.

Do not replace batteries when seat is occupied.

Power chair batteries are heavy. See speciﬁcations

table. If you are unable to lift that much weight, be sure

to get help. Use proper lifting techniques and avoid

lifting beyond your capacity.

Do not mix old and new batteries. Always replace both

batteries at the same time.

Keep tools and other metal objects away from the battery

terminals. Contact with tools can cause electrical shock.

To replace the batteries:

1. Turn off the power to the controller.

2. Make sure that the power chair is in drive mode. See

“Your Power Chair.”

3. Remove the front cover by squeezing the release

handles (see ﬁgure 24) and lifting the front cover up

and away from the power base.

4. Disconnect the quick release battery connectors. See

ﬁgure 24.

5. Remove the batteries.

6. Disconnect the battery harness from each battery.

7. Connect the battery harness to the new front battery

according to the battery wiring diagram. See ﬁgure 24.

Make sure you tighten the fasteners so that the

connections are secure.

8. Connect the battery harness to the new rear battery

according to the battery wiring diagram. See ﬁgure 24.

9. Install the new batteries and connect the quick release

battery connectors.

10. Reinstall the front cover.

11. Charge the batteries. See “Batteries and Charging.”

PROHIBITED!

When to See Your Quantum Rehab Provider for Service

The following symptoms could indicate a serious problem

with your power chair. If necessary, contact your Quantum

Rehab Provider. When calling, have the model number,

serial number, nature of the problem, and the error code if

available.

 Motor noise

 Frayed harnesses

 Cracked or broken connectors

 Uneven wear on any of the tires

 Jerky motion

 Pulling to one side

 Bent or broken wheel assemblies

 Does not power up

 Powers up, but does not move

 Loose seat or seating components

Corrective Maintenance

If the battery condition meter does not light up when you turn

on the power:

 Check the harness connections. Make sure they are

tight.

 Check the circuit breaker. Reset it if necessary.

 Check the battery connections.

If the above conditions prove normal, you can load test the

batteries with a battery load tester. These testers are available

at automotive parts stores. Disconnect both batteries before

load testing and follow the directions that come with the load

tester. If either one of the batteries fails the load test, replace

both of them. If your power chair still does not power up,

contact your Quantum Rehab Provider.

WARNING!

MANDATORY!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quantum Q6 Edge 2.0 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quantum Q6 Edge 2.0

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info