Bedienungsanleitung Quickie All Court (Seite 15 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

713894

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

930493 Rev. A

ENGLISH

. SEAT SLING

The seat sling can be adjusted through the use of VELCRO® style retaining material beneath the seat.

Adjustment

a. Remove the screws retaining the left side seat sling.

b. Readjust VELCRO® style material to adjust the tension in the seat sling.

c. Replace screws and torque to 45 inch-lbs (5 N-m).

d. If there is any difficulty in reattaching the screws, try using a probe to help line up the holes.

G. CUSHION (OPTIONAL)

Installation

a. Place cushion on seat sling with VELCRO® side down. The beveled edge of the cushion should

be in front.

b. Press firmly into place.

H. REAR AXLE ASSEMBLY

1. Center of Gravity Adjustment

The most important adjustment on your Quickie All Court is the position of your center of gravity.

The position of your seat frame will determine your center of gravity.

• The further forward the seat, the more stable the chair becomes.

• Moving the seat frame back will increase your turning speed and lighten the front end.

For example: Using hole 1 will increase your turning speed.

Using hole 8 will give you a more stable ride.

2. Wheel Camber

Increasing wheel camber angle provides greater side-to-side stability due to the increased width and

angle of the wheelbase and also allows for quicker turning and greater access to the top of the handrims.

The wheel camber option from the factory is 16° & 20°.

3. Rear Wheel Axle Sleeve Adjustment

Tight axle sleeves (1) should be maintained for proper performance of the wheelchair.

a. To adjust axle sleeve, you will need a 1 1/8" open end wrench to turn the outside axle sleeve nuts

(2).

b. You will also need a 5/8" wrench to hold the axle sleeve in place while loosening or tightening

the axle sleeve nuts.

c. Loosen nuts and adjust axle sleeve in or out to desired location. Distance should be equal on

both axle sleeves.

d. Hold axle sleeve with 5/8" wrench and tighten nuts.

4. Toe-in and Toe-out

oe-in and T

oe-

out are terms that relate to how well the rear wheels of the chair are aligned. This will

affect how well the chair will roll. Drag or resistance occurs in a wheelchair when the rear wheels are

not properly aligned.

Toe-in or toe-out can be adjusted by loosening the axle-sleeve nut and then slightly rotating the axle

sleeve forwards or backwards.

a. Toe-in: To eliminate toe-in, rotate the top of the axle-sleeve toward the rear of the chair.

b. Toe-out: to eliminate toe-out, rotate the top of the axle-sleeve toward the front of the chair.

To check that the rear wheels are properly aligned, measure the centerline to centerline of the tires at

the midpoint front and rear until the desired measurement is achieved.

(Detail)

Camber Tube

16° & 20°

Eccentric Axle Sleeve

Toe-out

Toe-in

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quickie All Court Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info