Bedienungsanleitung Quickie Krypton R (Seite 11 von 72) (Englisch, Holländisch, Französisch)

713876

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

11Krypton R Rev.B

Suspension System

WARNING!

Rear suspension can affect the stability of the wheelchair. To

avoid a fall, use a spotter and/or anti-tip tubes when becoming

familiar with new equipment.

1. Tuning the 4-Link Rear Suspension

a. to stiffen the suspension, turn the spring preload adjustor (E)

clockwise (looking up at the suspension system from

underneath the wheelchair).

b. to soften the suspension, turn the spring preload adjustor (E)

counter-clockwise (looking up at the suspension system from

underneath the wheelchair).

2. Alignment of Suspension Link Arms

Do not adjust the link arms (F, Fig. 4.10). These are set at the

factory to ensure proper tracking and performance of the 4-Link

Rear Suspension system.

(see next page).

Setting the toe-in/toe-out to zero (with the adjusting device

installed in the factory)

Loosen the Allen screws (G) (2 on each side)

which are used to secure the axle tube on both sides. Observe

the ball in the transparent adjuster in the centre of the axle tube,

then turn the axle tube (C), until the ball is exactly centred at the

lowest point of the adjuster. The toe is now set at zero (Fig. 4.7,

4.10).

Before re-tightening the screws (G), check

that the flat surfaces of the wheel camber adapter in the axle

tube protrude from the clamp of the axle tube. The end of the

cylindrical camber adapter should be flush with the end of the

axle tube. Tighten the screws to a torque of 7 Nm.

Setting the toe-in/toe-out to zero (using a 90° setting gauge)

Place the entire wheelchair on a flat

horizontal table or ground surface. Loosen the Allen screws (G)

(2 on each side) which are used to secure the axle tube on both

sides.

Then put the setting gauge at an angle of exactly 90° (e.g. a

carpenter's square) on the flat surfaces of the camber adapter

(D) (Fig. 4.8, Fig. 4.9). Then turn the axle tube until the surfaces

of the wrench are entirely parallel to the upper surface of the

setting gauge (Fig. 4.8).

Before re-tightening the screws (G), check

that the flat surfaces of the wheel camber adapter in the axle

tube protrude from the clamp of the axle tube. The end of the

cylindrical camber adapter should be flush with the end of the

axle tube. Tighten the screws to a torque of 7 Nm.

CAUTION!

When turning the 4-Link Rear Suspension, always make one

change at time and write down the change. This takes patience,

but allows you to understand how each change affects the ride of

the wheelchair in conjunction with rear suspension.

NOTE – The lower shock mount is designed to have a loose feel,

this is by design to allow for proper suspension travel.

CAUTION!

The screw connection between the axle clamp and the shock

absorber should never be loosened.

3. Maintenance

The following maintenance work must be carried out, along with

the general maintenance tasks described in section 6.0.

a. do not apply lubrication to shock end bushings or coils.

b. you can apply lubrication to the link ends after cleaning with a

mild soap and soft

brush.

c. use a soft brush to clear any dirt or debris from coil system.

d. never use a high-powered washer for cleaning the 4-Link Rear

Suspension.

Fig. 4.8

Fig. 4.7

BALL

Fig. 4.10

Fig. 4.9

PARALLEL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quickie Krypton R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info