GB
Placing / removing the Quinny Dreami carrycot (see illustrations 17 - 18)
and Maxi-Cosi child car seat (see illustrations 19 - 20)
• Apply the brake on the Quinny Speedi (see Using the parking brake).
• Place the carrycot /
child car seat
onto the adapters (17/19) with the foot end between the sides of the handle.
• Check to make sure the carrycot /
child car seat
is secured by lifting it up by the handles.
• To remove, place your thumbs on the control buttons on both sides of the carrycot /
child car seat
(18,1/20,1).
• Push in the buttons while lifting the carrycot /
child car seat
from the Quinny Speedi (18,2/20,2).
When used as a pushchair (see illustrations 21 - 29)
Placing / removing the pushchair seat
• Apply the brake on the Quinny Speedi (see Using the parking brake).
• To remove the pushchair seat undo the velcro under the foot rest (21,1) and undo the clasp (21,2) and the
press stud (21,3).
• Open the press studs on the bottom (22,1) and undo the velcro near the handlebar safety lock (22,2).
• Remove the pushchair seat from the frame.
• When placing the pushchair seat back onto the frame, make sure to re-attach all press studs, clasps and velcro.
• IMPORTANT: Make sure you remove the adapters before attaching the pushchair seat (see Placing / removing
the adapters).
• Check to make sure everything is securely fastened by lifting up the pushchair seat.
Safety harness
• Apply the brake on the Quinny Speedi (see Using the parking brake).
• Make sure the safety harness is loosened before placing your child (carefully!) into the seat.
• Slide the buckle sections together (23,1) and fasten the lap and shoulder belts into the crotch strap by clicking
the buckle sections into the fastener (23,2).
• Adjust the belts to the size of your child by lengthening or shortening the belts using the clasps (24).
• Push the buttons (25,1) to open the fastener (25,2).
• There are D-rings for securing an additional safety harness. Make sure the safety harness complies with all
safety standards (i.e. BS 6684) before using it.
• The shoulder belts are height adjustable. To change the height, open the cover on the back and adjust the clasp
both on the front in the cover and in the board. Tilt the clasp when adjusting (26).
• IMPORTANT: The press studs on the side of the seat are for attaching a footmuff only (27).
Footrest
• The footrest can be adjusted into 2 positions.
• P
ress both buttons under the footrest at the same time (28,1), and then adjust the footrest into the desired
position (28,2).
• IMPORTANT: Never let your child sit or stand on the footrest.
Cover
• Remove the pushchair seat from the Quinny Speedi (see Placing / removing the pushchair seat).
• Remove the safety harness (see Safety harness).
• Remove the support plate from the back (34).
• The cover and basket can be washed by hand in lukewarm water using a regular detergent (see Washing
instructions).
• To re-attach the cover, slide the board back in.
• Re-attach all clasps, press studs and velcro.
• IMPORTANT: Make sure the safety harness is secured properly.
• IMPORTANT: Never use the pushchair seat without the support plate.
Back rest adjuster
• The pushchair seat back can be adjusted continuously from a sitting to a reclining position.
• To adjust the back rest, squeeze the adjusting section on the back (29,1) and adjust the strap until the seat is in
the desired position (29,2).
/ 9
ENGLISH
EXI0120_GBA_SpeediSX_BW_II.qxp:EXI0120_GBA_SpeediSX_BW_II 04-10-2006 15:17 Pagina 9