Bedienungsanleitung Radson 51055 - SLAVE RF (Seite 7 von 40) (Deutsch, Englisch, Holländisch, Französisch)

500597

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Names

Description

Default setting & Other possibility

The following parameters are only visible if a water contact sensor (NTC 10K sensor) is connected and

installed on the incoming pipe of the manifolds, and if the parameter “HC” is on “SenS” position.

(See the schematic and system drawing to install the sensor)

Setting Level to switch your installation between Heat and

cool mode.

When the water temperature (Wtemp) on the incoming pipe

decrease below this setting (minus the hysteresis value/2),

the installation will work in cooling mode.

Wtemp < HCL – HCh/2 => System in cooling mode

Wtemp > HCL + HCh /2 => System in heating mode

Press (OK) to view the instantaneous value measured by

the sensor.

Default: 22°C

Adjustable: 5 to 35°C

Hysteresis value for the setting level “HCL”, to avoid quick

commutations between Heat & Cool change.

Default: 5°C

Adjustable: 3 to 10°C

The following parameters are only visible if a water humidity sensor (NTC 10K sensor or free contact

sensor) is connected and installed on the incoming pipe of the manifolds

(See the schematic and system drawing to install the sensor)

Setting level to switch off the cooling function to avoid

residual humidity in the house:

When the water temperature in the pipe decrease under this

level during the time of the anti short cycle adjusted on “rHt”

the cooling function will be stopped.

Press (OK) to view the instantaneous value measured by

the sensor.

Default: 18°C

Adjustable: 5 to 25°C

Minimum time to decide to stop the cooling function when

the water temperature decreases under the “rHL” level.

Default: 5°C

Adjustable: 3 to 10°C

Delay time (in seconds) for the pump start up after the first

heat demand from minimum one zone.

This function is generally used to avoid noise and damage

of the hydraulic parts of the installation.

Default: 60 s

Adjustable: 0 to 240s

Press (OK) during 5 seconds to reset the installation.

All parameters are replaced by default value.

Press (OK) on this parameter to exit the parameters menu end come back to the main

display.

7. RF ALARM

- You could see the RF alarm on the Master (Red blinking LED on the concerned zone) and on the RF main

zone programmer (in the status line).

- If a RF alarm is detected on one zone, the regulation will be maintained on this zone by average of the actual

room temperatures of the other zones used on the Master.

- Check the thermostat batteries of the concerned zone. If batteries thermostat must be changed, always

replace the 2 batteries in the same time. The RF alarm message should be disappear alone when batteries will

be replaced.

Note:

If all zones are in RF alarm (Red blinking) check the RF antenna connection before replacing of all thermostat

batteries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Radson 51055 - SLAVE RF Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info