Bedienungsanleitung RAINBIRD MiniPro (Seite 1 von 2) (Englisch)

685862

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CHANGING A NOZZLE

1. REMOVING THE NOZZLE RETENTION SCREW

Use your K-Key (K) or a small flat blade screwdriver to remove

the nozzle retention screw (C) by turning counter-clockwise to

remove and clockwise to re-install.

2. PULL UP THE RISER

Insert the K-Key (K) in the keyhole (D) on the top of the nozzle

turret (M) and turn the key ¼ turn to insure that the key does

not slip out of the keyhole when you pull it up. Firmly pull up

the entire spring-loaded riser to access the nozzle socket (N).

Hold the riser assembly with one hand.

3. REMOVING THE NOZZLE

Insert the end of the K-Key (K), hook side up, into the tall slot

along the right side of the nozzle (J) and pull up to pop out the

nozzle. NOTE: Do not put the K-Key or any instrument into the

nozzle opening.

4. INSTALLING A NOZZLE

Press the desired nozzle into the nozzle socket (N). Make sure

the nozzle number is visible and the nozzle “wing” is up.

Then, re-install the nozzle retention screw (C).

NOTE: The nozzle retention screw is also a break-up screw

and used to adjust the distance of the spray.

SETTING THE ARC ADJUSTMENT

1. FINDING THE LEFT START POSITION

Place your finger on the top center of the nozzle turret (M).

Rotate the turret to the right until it stops and then back to

the left until it stops. Notice the position of the nozzle arrow.

This is the “Left Start” (L) position. The sprinkler will begin

spraying from this position and rotate clockwise until it

reaches the right “Arc Stop” (F).

2. ORIENTING THE LEFT START POSITION

Insert the K-Key (K) in the keyhole (D) on the top of the nozzle

turret (M) and turn the key ¼ turn to insure that the key does

not slip out of the keyhole when you pull it up. Being careful

not to allow the nozzle turret to turn, firmly pull up the entire

spring-loaded riser. Hold the lower riser assembly up with

one hand. Now turn only the lower riser (O) clockwise or

counter-clockwise until the nozzle arrow is pointing where

you want the sprinkler to begin spraying.

3. CHANGING THE ARC

Insert K-Key (K) or a flat blade screwdriver into the Arc Set

Adjustment slot (I). Turn clockwise to increase the arc or

counter-clockwise to decrease the arc. NOTE: The arc set

arrow in the center of the nozzle turret rotates to show

the correct setting.

Ra Flow

K L/M M

R F

Ra Flow

K L/M M

R F

30° – 360°

Ra Flow

K L/M M

R F

A TURRET TOP

ARC SELECTION:

30° TO 360°

Nozzle

Position

Keyhole

Arc Set

Adjustment

K K-KEY

J NOZZLE

Nozzle

Retention

Screw

MINIPRO

™

GEAR DRIVEN SPRINKLER SETTING INSTRUCTIONS

NOTE: The MiniPro is factory preset with a 40° arc setting, and includes a pre-installed #1.5 nozzle.

Arc Set

Arrow

Arc’s

Adjustable

Range

Ra Flow

K L/M M

R F

Housing

Can

Sprinkler

Assembly

Twist-Lock

Top

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

RAINBIRD MiniPro Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info