Bedienungsanleitung Raleigh 2021 General Bikes-Ebikes (Seite 51 von 70) (Englisch)

780098

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Originalbetriebsanleitung Allgemein EN-51

26.2.2 Drop-out II: adjusting the belt tension

1. Pedelec/S-Pedelec: Remove the battery.

2. Loosen the four screws on both sides of the rear

stays by turning these counterclockwise. There are

two screws behind the plastic cover, and one of the

screws on the other side holds the side stand plate in

position. Do not remove the bolts completely.

3. You can increase or decrease the belt tension by

turning both setting screws.

Fig. 112 Setting the belt tensioning

2. Adjusting the setting

screws

1. Loosen screws

4. Tighten the four screws on both sides of the rear stays

clockwise to the specied tightening torque.

Plate xture

9.5 NM

Belt tensioning

16.5 NM

Belt

tensioning

16.5 NM

Fig. 113 Setting the belt tensioning

26.3 Checking the belt for wear

1. Pedelec/S-Pedelec: Remove the battery.

2. Check the belt for wear.

Fig. 114 Belt with no wear ©Gates

This belt is in good condition. The loss of blue colour is

not a sign of wear.

Fig. 115 Worn belt ©Gates

Missing teeth and cracks in the tooth root: This belt

is in a very poor condition.

3. When the safe wear limit has been reached, the belt

must be replaced. Have this done in your specialist

workshop.

26.4 Cleaning and care

Notice

Damage to the electronics due to water ingress.

▪Do not spray the bicycle or its components, either

with a water hose or with a high-pressure cleaning

device. Although the components are sealed,

damage to the cycle may still result. Clean the bike

with a soft damp cloth.

Please remove the battery before cleaning the belt on a

Pedelec or S-Pedelec. Then, clean the belt with a soft, damp

cloth. Allow it to dry before putting it back on your bike.

27. Wheels

Wheels provide the connection between your bicycle and

the road. They can be attached to the frame and fork using

axle nuts, quick-release skewers or through-axles.

27.1 Fastening wheels with quick-release

skewers

Warning

Serious falls due to loose components.

▪ All quick-release skewers must be properly closed

before setting o. Quick-release skewers cannot be

closed by simply turning the lever.

▪ Check that all quick-release skewers are rmly

seated before every use.

▪Do not bend the brake disc or hold onto it when

closing the quick-release skewer.

Wheels are attached to most bicycles using quick-release

skewers. These are clamping devices which have the

advantage that they can be quickly loosened and tightened

by hand. Quick-release skewers normally consist of ve

parts: the axle, the tensioning lever, the clamping nut and

two springs. The tensioning lever and axle are rigidly

connected to one another, while the clamping nut is

screwed onto the end of the axle. The tensioning lever

exerts a clamping force, and the clamping nut is used to set

the pre-tension.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Raleigh 2021 General Bikes-Ebikes Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Raleigh 2021 General Bikes-Ebikes

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info