Bedienungsanleitung Ravelli FLAVIA (Seite 20 von 76) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Spanisch)

597715

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Pag.20

This type of installation (see fig. 7) does not require an insulated flue for

the part inside the house, whilst for the part outside, an insulated tube

must be used. In the lower part of the flue in the house, a union tee has

been installed with a peephole, but another one has also been installed

outside, so that the part can be inspected.

Two 90° bends should not be installed as the ash could quickly block the

passage of smoke, causing problems for the draught of the stove.

Operating faults due to flue draught problems or critical wea-

ther conditions

Among all weather and geographical conditions that may have an impact on

the operation of the draught ﬂ ue (snow, rain, altitude above sl, fog, …) wind

is certainly the most important. In fact, in addition to the thermal depression

caused by the temperature difference between the inside and the outside of the

ﬂ ue, there is another type of depression: dynamic depression caused by wind.

Therefore, wind has an impact on the efﬁ ciency of the ﬂ ue.

THE OPERATION OF THE PELLETS STOVE IS THEREFORE STRONGLY

DEPENDENT ON THE POSITION AND CONSTRUCTION OF THE FLUE. PRECARIOUS

CONDITIONS CAN ONLY BE RESOLVED WITH AN APPROPRIATE SETTING OF THE

STOVE BY RAVELLI APPROVED TECHNICAL PERSONNEL.

7. DESCRIPTION OF THE FUNCTIONING AND SYMBO-

LOGY OF THE DISPLAY

The innovation of this particular display is the communication through low volt-

age conveyed waves (12 volts) between the electronic motherboard and the

display. The communication is made trough a bipolar cable (ex: the cable for

the stereo speakers) and the novelty is the possibility to install the display in

the wall using the optional standard frame for electrical box 503.

7.1. Display with mode “BASE”

Calender

Room temperature

Clock

Working power

Stove status

Key “1”:

access key to “set room temperature” and regulation

Key “2”:

access key to “set power” and regulation

Key “OK”:

short press of the key to confirm and come back to the main

screen; press the key 3 seconds long to switch on and switch

off the stove.

The functionalities of this display when used in mode “BASE” are:

•

Switch on and switch off of the stove

•

Set of the room temperature and selection of the type of sensor (sup-

plied sensor connected to the motherboard or sensor integrated to the

display)

•

Set of the working power (1,2,3,4,5)

7.1.1. switch on and switch off of the stove

Before starting the stove please follow following procedure :

Connect the power cable

Set the switch on the backside of the stove on position 1

Check that the installation is connected to the chimney

Load the pellet tank with 6 mm pellets

Load the screw as described in paragraph 8.6

Press key OK for 3 seconds long.

At this stage the stove will begin the ignition phase.

On the display will appear following writings:

•

START

(waiting time is different depending on default settings)

•

WAITING FLAME

(waiting time is different depending on default settings)

•

FLAME LIGHT

(waiting time is different depending on default settings)

•

WORK

(waiting time is different depending on default settings)

7.1.2. Set of the room temperature

Fig. 1 Fig. 2

The functioning of the stove with room thermostat activated is of 3 types:

•

With supplied room sensor positioned on the backside of the stove ( not

available for insert models)

•

With room sensor integrated to the display

•

With external thermostat (not supplied)

MODE WITH SUPPLIED ROOM SENSOR (DEFAULT AND SUGGESTED

USE)

If you use the supplied room sensor , the display will show the room tem-

perature. To set and modify the room temperature press key number 1 to

enter in the dedicated menu and set the desired value with key 1 and 2.

Confirm with key OK 2 times and keep deselected the box SENSOR CON-

SOLLE (flag, see pic.2). Once reached the set temperature the display

will show MODULATION WORK, so the stove will reduce to minimum the

pellet consumption and the power as well.

MODE WITH ROOM SENSOR INTEGRATED TO THE DISPLAY

in case you want to install the display on the wall instead of on the stove

as from the factory, please reference to the functioning with supplied room

sensor (as above explicated) with just one difference: the box (flag)

SEN-

SOR CONSOLLE

, if you work in this mode, should be selected by using

key 2. Then confirm with the key OK ( reference to pic. 1 paragraph 7.1.2.)

EXTERNAL THERMOSTAT MODE

if you use an external thermostat correctly connected as shown in the

electrical scheme ( reference paragraph 10), the display will not show the

room temperature but the writing T ON ( when the contact is closed) or T

OFF ( when the contact is open).

REMARK: TO ENABLE THE EXTERNAL THERMOSTAT ENTER IN THE

SET TEMPERATURE USING KEY 1 AND THEN PRESS REPEATEDLY

TO REACH THE VALUE “EST” ON THE DISPLAY; CONFIRM TWO

TIMES WITH THE KEY OK KEEPING DESELECTED THE BOX (FLAG)

“SENSOR CONSOLLE”.

Once reached the set temperature of the thermostat the display will show

MODULATION WORK, so the stove will reduce to minimum the pellet

consumption and the power as well. If activated the mode COMFORT

CLIMA, the stove will switch on and off automatically (for details reference

paragraph 8.2.)

1 2 3 5 6 7 8 9 104

-TC1+TERM.N.AMB.

SMOKE

PROBE

ROOM

TERMOSTAT

ROOM

PROBE

-TC1+TERM.N.AMB.N.H2ON.PEL.

Red

Blue

Black

WE ADVISE A ROOM TERMOSTATE WITH OFF-SET WITH OF MINIMUM

3°C IF WE WANT ACTIVATE CONFORT CLIMA,PROPERLY.

Insulated ﬂ ue

Union tee for conden-

sation of insulation

H > 4 mt

H > 1,5 mt

2-3 metres

Max

3-5% gradient

Union tee for condensation

Ravelli FLAVIA Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info