470000
16
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
Prevent the cable chang where it enters and exits the mast.
Minimize electrical interference by:
Not running the cable near other electrical equipment.
Not running the cable alongside power cables or antenna
cables for other equipment.
Power requirement
The HD Digital Radome Antenna must be supplied with power by
either a 12 V dc or a 24 V dc supply. Do NOT connect to a 32 V
system.
If you are replacing an existing Radome scanner with an HD Digital
Radome Antenna, you must also replace any existing cable with the
appropriate digital cable, as described in section 2.7 Cables.
If you connect to the power supply via an isolator switch, the
minimum switch rating is:
For a 12 V system, 20 A.
For a 24 V system, 15 A.
Caution: Do NOT connect to positive
ground system
Do NOT connect this product to a
positively-grounded system.
Power Supply Protection
The power supply must be protected by a suitable thermal circuit
breaker or fuse, tted close to the power source. The protection
requirements are the same for both 18” and 24” HD Digital Radome
Antennae, and are as follows:
In a 12 V system, protect the power supply with either a 10 A
thermal breaker, or a 15 A fuse.
In a 24 V system, protect the power supply with either a 5 A
thermal breaker, or an 8 A fuse.
Power cable lengths
The total permitted lengths of power conductor run (i.e. power cable
plus cable extension) from the power source to the HD Digital
Radome Antenna are :
for 12 V systems, 20 m (65 ft)
for 24 V systems, 35 m (115 ft)
If you want to connect to a 12 V power system but a total power
conductor run of more than 20 m is necessary, the use of a suitable
voltage converter is recommended, to convert the 12 V supply
voltage to 24 V, and thus enable you to extend the run up to 35 m.
We recommend using a converter with a minimum 200 W output
capacity.
Grounding
These grounding requirements are applicable for Raymarine
equipment supplied with a separate drain wire or screen.
• The product power cable drain conductor (screen) must be
connected to a common ground point.
It is recommended that the common ground point is a bonded
ground, i.e. with the ground point connected to battery negative,
and situated as close as possible to the battery negative terminal.
If a bonded ground system is not possible, a non-bonded RF
ground may be used.
16
HD Digital Radome Users Guide
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Raymarine HD Digital Radome Antenna wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info