Bedienungsanleitung Red One 30.5 - 2010 (Seite 145 von 150) (Englisch)

597820

145

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Build 30 v30.5.0

143

APPENDIX G: POSSIBLE ERRORS, ISSUES AND SOLUTIONS

For errors or issues beyond those listed below, please contact support through our web site at

www.red.com/support.

• Camera shuts down upon movement - Battery is not seated properly to the battery plate. Disen-

gage and reengage the RED-BRICK to the BATTERY PLATE.

• Error Message: “Black Shading Failed” - Check recording media/connections and reattempt Black

Shading. Refer to BLACK SHADING ERRORS in BLACK SHADING under MAINTENANCE in SETUP

under SYSTEM MENU CONTROLS.

• Error Message: “Unable to Calibrate” – Ensure a formatted CF card is installed in the camera when

performing a Black Shading. If a formatted CF card is not installed, this error will be displayed.

• The image looks soft - Re-adjust back focus and make certain the lens is properly collimated. Refer

to BACK FOCUS ADJUSTMENT under BASIC OPERATION.

• Error Message: “Record Error: NO_DIGMAG” - No media is being detected. Reattempt to mount,

check connection and CF pins in Module, power cycle, or try another media.

• Error Message: “Valid Settings” - Establish the maximum PROJECT settings for the media you are

using and change the settings accordingly. Refer to PROJECT SETUP under BASIC OPERATION.

•

• Error Message: “Record Error: RE: INCOMPATIBLE_DIGMAG” - Make sure that you establish the

original time base for the media’s project or reformat media. Refer to MEDIA ERRORS under APPEN-

DIX B: MANAGING DIGITAL MEDIA.

• Error Message: “The Magazine Formatting Failed - No digmag found. Nothing to format” - The

magazine was not recognized during formatting, check your media and connections. Refer to AP-

PENDIX B: MANAGING DIGITAL MEDIA.

• Error Message: “The Magazine Formatting Failed - The magazine isn’t fast enough to support

the current project. Please change the project settings before formatting this media.” - Check to

make sure you have the valid PROJECT settings for that particular piece of media. Refer to PROJECT

SETUP under BASIC OPERATION.

• Error Message: “WARNING! Media removed prior Unmount Data Integrity Risk” - Media needs to

be removed properly. Use the dual key command UNDO+EXIT, or the menu option SYSTEM > MEDIA

> UNMOUNT. Refer to APPENDIX B: MANAGING DIGITAL MEDIA.

• Error Message: “The CF Card has not been Speed Verified for use on this camera. Only 2k reso-

lution recordings are possible. There is an unquantifiable risk of drop frames” - This may occur if

you are using Non-RED CF cards and/or you have a damaged CF card.

• Error Message: “Record Error: NO_MEDIA_PATH” - When you have a card in the camera that is

reading unformatted and you should continue by formatting the media. Refer to APPENDIX B: MAN-

AGING DIGITAL MEDIA.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Red One 30.5 - 2010 Seite 145

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info