814905
6
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
10 11
QUESTION
Why does the blower fan not work
after I have turned on the heater
power button?
ANSWER
The blower fan will not work until
the heating element is hot enough to
heat the air passing by. It will normally
turn on after about 10 seconds.
Why does the blower fan keep
running after I have turned off the
power button?
The blower fan will continue to run
until the proprietary heat chambers
have cooled down. After a few minutes
the fan will shut off automatically.
Why has the heater airflow seem to
have diminished? Make sure the rear intake is not
blocked and that the filter is clean.
Follow the filter maintenance
procedure to clean the filter.
TROUBLESHOOTING
The heater has shut itself off and a red
LED light is illuminated on the front of
the heater. What does this mean?
The heater has gone into Auto
Recovery mode. This occurs when the
internal temperature of the heater
exceeds a pre-defined limit. Simply wait
a few minutes for the internal
components to cool down, and restart
the heater. Check to make sure no
other appliances are operating on the
circuit used to run the heater, as this
could also cause overheating. Be sure
to clean the air filter on the back of the
heater, as this could cause the unit to
overheat.
Once I initially plug the unit in and turn
it on, how long will it take to heat
my room?
Generally, it takes less than an hour.
Please remember that with any type
of heating process there are many
variables: size of the room, how well
the room is insulated, how many
doors/windows, how much bare
concrete (which acts as a heat sink
with any type of heating), the opening
and closing of an exterior door, and
the outside temperature etc.
WARNING TO USER
PERFORMANCE SUGGESTIONS
To assure maximum performance of the heater, please note the following
recommendations:
1. For best results, do not locate the heater in an area with a high rate of air filtration
and movement as the warm air will be exhausted.
2. Try placing the heater near a warmer inside wall and direct the output towards a
cooler outside wall. The cooler outside wall will tend to draw the generated heat
towards itself, which will allow for more efficient heating.
3. Placing the heater next to a cold air return will draw the heat away from area to be
heated. Try closing or covering the cold air return. This will allow for more efficient
heating. Experiment with the placement of the heater to see what works best for you.
4. To ensure maximum efficiency, a 40% (minimum) relative humidity should be
maintained in the heated environment.
5. When the heater is placed in an isolated area, i.e. basement or recreation area, the
delivery registers and air return grills of the existing system should be closed in that
area if possible.
6. Try placing the heater a few feet above the floor in rooms with large areas of bare
concrete. Make sure the heater is secure and won't fall. This will allow for more
efficient heating since concrete acts as a heat sink and will tend to draw the heat in
its direction.
7. Try lowering your central heating system to a lower temperature and placing the
heater in the area you spend the majority of your time. Now set the heater to your
comfort level. This will help reduce your overall energy consumption.
8. When heating larger areas, place the heater in a central location. If a ceiling fan is
nearby, try using it at the same time to help distribute the heat evenly.
9. If used in an extremely dirty or dusty area, the filter must be cleaned more frequently
as the filter can clog and cause the heater to stop working. Please refer to “How to
Clean the Air Filter” in this manual for cleaning instructions.
10. The heater grill is hot when in use. To avoid burns, do not let bare skin touch the hot
surface. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes,
and curtains at least three feet from the front of the heater and keep them away from
the sides and rear.
11. CAUTION: Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and unattended.
12. To disconnect heater, turn controls to off, then remove plug from outlet.
Always unplug heater when not in use.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Redcore 15301-15314 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info