Bedienungsanleitung Reebok 910 TREADMILL (Seite 20 von 36) (Englisch)

559703

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do

not do this, you may damage the console displays

or other electrical components.

Plug in the power cord

(see page 18). Next, locate

the power switch on the

treadmill frame near the

power cord. Press the

power switch into the reset

position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and press the power

switch into the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

25 to turn off the demo mode.

Next, stand on the foot

rails of the treadmill.

Find the clip attached

to the key and slide the

clip onto the waistband

of your clothes. Then,

insert the key into

the console. After a

moment, the displays

will light.

IMPORTANT: In an emergency, the key can be

pulled from the console, causing the walking belt

to slow to a stop. Test the clip by carefully taking

a few steps backward; if the key is not pulled from

the console, adjust the position of the clip.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER at the left.

2. Select the manual mode.

If the manual mode is not selected, press the

Manual button on the console.

3. Start the walking belt.

To start the walking belt, press the Start button, the

Speed increase button, or one of the 1 Step Speed

buttons numbered 1 through 12.

If you press the Start button or the Speed increase

button, the walking belt will begin to move at 1 mph.

As you exercise, change the speed of the walking

belt as desired by pressing the Speed increase

and decrease buttons. Each time you press one of

the buttons, the speed setting will change by 0.1

mph; if you hold down the button, the speed setting

will change in increments of 0.5 mph. Note: After

you press the button, it may take a moment for the

walking belt to reach the selected speed setting.

If you press one of the numbered 1 Step Speed

buttons, the walking belt will gradually change

speed until it reaches the selected speed setting.

To select a speed setting that includes a decimal—

such as 3.5 mph—press two numbered buttons in

succession. For example, to select a speed setting

of 3.5 mph, press the 3 button and then immedi-

ately press the 5 button. Note: This will not function

if the console is set to metric units.

To stop the walking belt, press the Stop button. The

time will begin to ash in the display. To restart the

walking belt, press the Start button or the Speed

increase button.

Reset

ETRB99013

(RBTL99013)

Key

Clip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Reebok 910 TREADMILL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info