Bedienungsanleitung Reef One Biorb Cube (Seite 19 von 142) (Alle Sprachen)

693174

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

- EN -

MAINTENANCE AND CLEANING

Cleaning and maintenance work:

Area

Tasks to be carried out

Lighting unit

Clean when necessary.

Change the batteries in the

remote control when neces-

sary.

Aquarium water

Partially change every 4 to 6 weeks.

Together with the filter cartridge.

Filter cartridge.

Replace every 4 to 6 weeks depend-

ing on the number of fish.

Air stone

Replace every 6 months.

Aerator pump

Replace every 12 months if neces-

sary.

Filter cartridge, water treatment sachets and a clean-

ing pad are available as OASE biOrb Service Kit (46014).

Preparing the water

Prerequisite:

Fresh water has been treated with "Water Condi-

tioner" 24 h beforehand and has reached room tem-

perature. Required quantity: Approx. one third of the

aquarium volume.

How to proceed:

 G

1. Remove the water to be replaced and clean the

aquarium with the cleaning pad for acrylic glass if

necessary.

OASE recommends:

• biOrb cleaner pump (46025)

• Cleaning pads (46027, only use the rough side for

particularly stubborn deposits).

2. Top up the aquarium with the treated water.

Replacing the filter cartridge

NOTE

• Switch off the aerator pump before commencing

with this maintenance work.

• Switch on the aerator pump again after completing

the work.

How to proceed:

• Remove the packaging from the filter medium.

 H

1. Release the bubble tube from the filter housing by

a quarter turn counterclockwise (bayonet closure)

and remove and dispose of the old filter cartridge.

2. Release the bubble tube from the filter cartridge by

a quarter turn clockwise and lift out.

3. Place the bubble tube onto the new filter cartridge

and fasten by a quarter turn counterclockwise.

4. Insert the bubble tube into the aquarium and fasten

by a quarter turn clockwise.

Replacing the air stone

How to proceed:

 I

1. Remove the bubble tube and filter cartridge.

2. Pull off the air stone and replace.

3. Insert the filter cartridge into the bubble tube and

install the bubble tube.

Checking the non-return valve

A non-return valve is defective if water can flow out of

the aquarium into the air hose.

How to proceed:

 J

1. Switch off the aerator pump and pull the air hose

from the aerator pump.

2. Hold this end lower than the water level in the

aquarium.

3. If any water emerges, it is necessary to replace the

non-return valve. (→ Replacing the non-return

valve)

Replacing the non-return valve

Prerequisite:

• The aerator pump is switched off and the air hose

has been removed from the aerator pump.

How to proceed:

 K

1. If the defective valve cannot be removed, cut open

the air hose as near as possible to the defective non-

return valve and fit the new non-return valve there.

2. Replace the defective non-return valve.

– The non-return valve is supplied with the air hose

fitted.

– Ensure that it is correctly positioned.

3. Fit the air hose onto the aerator pump again before

switching on the aerator pump again.

WEAR PARTS

• Aerator pump

• Ceramic substrate

• Air stone

• Filter cartridge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Reef One Biorb Cube Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info