Bedienungsanleitung Reer 46101 (Seite 11 von 22) (Deutsch, Englisch, Dänisch, Französisch, Italienisch)

716159

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

- 9 -

English (EN)

(B)

(A)

Install the adjustment screws (d) with the nuts on the gate compartment (a) at the top and the

bottom. Ill. 1 and 2.

Art. No. 46201: Insert nuts (e) at the top and the bottom in the slits of the crossbar before

attaching the adjustment screws. Ill. 1 and 2.

Attach the hinge bolts (c) on the gate compartment (b) at the top and the bottom. Ill. 3 and 4.

Art. No. 46201: Insert nuts (e) at the top and the bottom in the slits of the crossbar before

attaching the hinge bolts. Ill. 3 and 4.

Note: The final adjustment of the fastening screw is executed later.

Place the gate compartments (a) and (b) flush next to each other so that there is no gap between

the gate compartments, Ill. 5 and 6.

Push these apart so that the distance between the last gate slat and the wall or door surface is at

least 30 mm and maximum 62 mm. Ill. 7

Connect the 2 gate compartments (a) and (b) with the connection screws (h) and the screw

sleeves (i) at the top and the bottom. Ill. 8 and 9. Ensure that the gate compartments are

attached firmly to each other and that the vertical slats are flush. Screw the screws tight with a

Phillips screwdriver.

Mark the drill holes on the hinge side with the help of the mounting template (o). These are

marked with the name “hinge”. Ill. 17, 18 and 19. First, only the lower hinge parts (f) are attached

using the wood screws (j). Ill. 17, 20 and 21.

(In another mounting surface use suitable screws and anchors)

The screw holes for the closing side must be marked using the mounting template (o). These are

marked with the name “latch”. Ill. 12, 13 and 14.

Optionally, the stoppers (m) can be inserted either on the left or right. For this purpose, insert the

stoppers (m) on the side in the hinge supports (k) and (l), Ill. 10 and 11, before they are

attached using the wood screws (j). Ill. 15 and 16.

Hang the hinge bolts (c) into the two lower hinge parts (f) on the gate. Then install the upper hinge

parts (g). Ill. 22 and 23. Adjust the adjusting screw so that the hinge supports (k) and (l) can lock

into place well at the top and the bottom. Ill. 24 and 25.

Step 1

Step 2

Step 3

Step 4

Installing the

hinge side

Step 5

Installing the

locking side

Installing the

stopper

Step 6

Installation on stairs

Especially well suited for installation at the top of stairs as it

opens completely and does not present a tripping hazard.

Here, the direction of opening shall be limited by the

installation of the supplied stopper (m) (Step 5)

(A) Install at the top of the upper the stair

and do not install on one of the stairs.

(B) If the safety barrier is used at the bottom

of the stairs, it should be positioned in the front

of the lowest tread possible.

Installation

ATTENTION: Always open the gate away from the dangerous position to avoid dangerous

situations!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Reer 46101 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info