Bedienungsanleitung REL Acoustics ST III Range (Seite 18 von 27) (Englisch)

457183

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

REL Acoustics ‘ST III’ User Manual

REL Set-Up Made Simple

RELs are not traditional subwoofers, but true sub-bass systems. A REL is designed to

augment the performance of “full range” speaker systems, to provide linear response down to

below 12 Hz (Studio III, -6 dB down at 9 Hz). Therefore, for the moment, set aside everything

you’ve been taught about subwoofers and how they are integrated into a stereo or theatre

system. RELs set-up and positioning differs from other subwoofers. A REL will take

advantage of physics and room acoustics to provide deep pressurisation as no other sub-

woofer can. It’s important that you bring to the set-up process a willingness to do things a little

differently in order to obtain these superior results. The end result of your labours will be an

utterly seamless integration of true deep bass to a sound system, regardless of the main

speaker’s low bass capability.

Two Things Before You Begin

A. It is helpful to know that you will almost always connect the REL to the input on the

rear panel labelled “Hi Level.” This connection is made using the supplied 34’ 10” (10

meters) cable, the bare leads of which connect to the speaker output terminals of the

power amplifier. The easy and foolproof connection at the REL is done with a Neutrik

Speakon connector. The purpose of connecting to the speaker output terminals is

one of the unique secrets of REL’s success. By connecting to the high level input on

the REL from the amplifier, you build forward the sonic signature of your main

system, including the tonal balance and timing cues of the entire electronics chain. In

this way, the REL is fed the exact signal that is fed to the main speakers.

B. When possible, the REL should be placed in one of the corners behind the speakers.

Remember, we are dealing with true LOW bass pressurisation with RELs, not the

mid-bass that most competitors settle for. Low bass pressurisation below 40Hz is

best derived from corner placement, where the most linear and efficient low bass can

be produced.

Basic set-up should take no more than ten to fifteen minutes to accomplish once connected.

Connecting

High-level connection, using the enclosed cable with the Neutrik Speakon connector,

is always the first choice. By connecting to the amplifier’s speaker outputs the sonic

signature of the entire amplification chain is folded into the signal for the sub, thereby

keeping timing and timbre cues consistent. In other words, the signal sent to the REL

is exactly the same signal sent to the speakers, allowing for seamless integration. This

connection can be made without affecting the performance of the amplifier because

the sub’s amplifier input impedance is 100,000 ohms. This scheme also avoids adding

any detrimental effects by not interposing any additional electronics into the

amplification chain.

• The standard high level hook up procedure is: attach the red wire to the amplifier’s

right positive speaker output terminal; attach the yellow wire to the amplifier’s left

positive speaker output terminal; attach the black wire to which ever of the amplifier’s

ground output terminals is convenient; plug the Speakon connector into the sub’s

high level input.

• For differential amplifiers using one sub, simply use the standard connecting scheme

with the exception of connecting ground to chassis ground, not to speaker output

ground, and then connecting into the high level input (Hi Input or Unbal Hi Input on

Stentor III and Studio III).

• For differential amplifiers using two subs, one for each channel: connect red to

positive; yellow to negative; and black to chassis ground; plug the Speakon into the

balanced high level input (Bal Hi Input).

Low-level connection, RCA inputs (or XLR on some models), is always an option, should

high-level connection not be possible, or in a theatre system where both high-level and low-

level connection should be used. When connecting to the low level inputs, connect a single

RCA cable to the 0dB RCA jack. Additional gain can be achieved by connecting to the +12dB

input. If you are connecting two channels of stereo output from a pre-amplifier, simply use a

high-quality y-adapter to sum the two signals together.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REL Acoustics ST III Range Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info