Bedienungsanleitung REL Acoustics Stentor III (Seite 21 von 27) (Englisch)

66881

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

REL Acoustics ‘ST III’ User Manual

REL Set-Up Made Simpler

Connecting

High-level connection, using the enclosed cable, is always the first choice. The

standard high level hook up procedure is: attach the red wire to the amplifier’s right

positive speaker output terminal; attach the yellow wire to the amplifier’s left positive

speaker output terminal; attach the black wire to which ever of the amplifier’s ground

output terminals is convenient; plug the connector into the “Hi Level” input. For

connection to a differential amplifier consult your dealer.

Positioning

Primary Placement, for a REL is in one of the corners behind the main speakers.

Phase Selection is the next step. Keep in mind; the correct phase is whichever position is the

loudest or fullest. While playing music with true low bass, adjust the crossover to a point

where the sub and the speaker are sure to share frequencies (B, 3 for big speakers; C, 4 for

smaller speakers). At this point adjust the gain so that both sub and speaker are roughly

equal in output and then switch, using the “mode selector” switch, from “0” (position 1) to

“180” (position 3) phase positions. Again, whichever position is loudest or fullest is the correct

position, and, as often as not, may be 180-degree phase (see enclosed “Control Panel”

section from the owner’s manual).

Orientation. With phase correct, it is important to site the woofer in the corner by determining

which wall, the side or the rear, the REL’s amp should face. Flip the sub back and forth in the

corner, and, again as with phase, whichever position sounds the loudest is the correct

orientation for the sub. For Q series, if possible, point the driver directly out of the corner,

equidistant from the side-walls.

Final Position. The next step is to determine precisely how far out from the corner the sub

should be to achieve the most efficient output, as well as the lowest frequency extension.

With the sub fully into the corner, continuing to play the music, slowly pull the sub from the

corner on the diagonal, equidistant from both side and rear wall. At a certain point (sometimes

a matter of only a few inches, in rare cases a foot or more) the sub will audibly go lower, play

louder, and, if it truly locks on to the room and is fully pressurising it, the air around the sub

will seem to be energised. Stop right there! This is the correct position for the sub.

Adjusting

Crossover Selection. To determine the crossover point, bring the gain down, put the

crossover to A-1 (or B-2 should output not be sufficient), and then bring the gain back up to

the point where you have achieved a subtle balance. Working only with the coarse control (A-

D), bring the crossover point up until it is obviously too high, at this point bring it down to the

next lowest setting. Now, working with the fine control (1-6), bring up the crossover point until

it sounds too high, at which point bring it back down to the next lowest setting. For all intents

and purposes, this is the correct crossover point. Once this stage has been reached, subtle

changes to gain and crossover can be accomplished to provide the last bit of complete and

seamless integration. For Q series, use the variable controls in much the same way, slowly

turning up both gain and crossover until excess output is realised, then back down a soft-click

or two.

Including Theatre

Multi-channel systems LFE output should be connected to the low-level input and appropriate

gain adjustments made at this point. It may be necessary to take the crossover out of the low-

level input using the “mode” switch if extra upper bass output is called for. Keep phase

consistent with what was selected during high-level set-up by simply choosing the

corresponding setting (1 = 2, 3 = 4). When connecting to the low level inputs, connect a single

RCA cable to the 0dB RCA jack. Should additional gain be required, connect to the +12 dB

input.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REL Acoustics Stentor III Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info