Bedienungsanleitung Rel quake (Seite 16 von 25) (Englisch)

413692

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

REL Acoustics ‘Q’ range User manual

REL Set-Up Made Simple

REL products are not traditional subwoofers, but true sub-bass systems. A REL is designed to

augment the performance of “full range” speaker systems, to provide linear response down to below

12 Hz (Studio III, -6 dB down at 9 Hz). Therefore, for the moment, set aside everything you’ve been

taught about subwoofers and how they are integrated into a stereo or theatre system. REL sub bass

systems set-up and positioning differs from other subwoofers. A REL will take advantage of physics

and room acoustics to provide deep pressurisation as no other sub-woofer can. It’s important that you

bring to the set-up process a willingness to do things a little differently in order to obtain these

superior results. The end result of your labours will be an utterly seamless integration of true deep

bass to a sound system, regardless of the main speakers low bass capability.

Two Things Before You Begin

A. It is helpful to know that you will almost always connect the REL to the input on the rear

panel labelled “Hi Level.” This connection is made using the supplied 34’ 10” (10 meters)

cable, the bare leads of which connect to the speaker output terminals of the power amplifier.

The easy and foolproof connection at the REL is done with a Neutrik Speakon connector.

The purpose of connecting to the speaker output terminals is one of the unique secrets of

REL’s success. By connecting to the high level input on the REL from the amplifier, you build

forward the sonic signature of your main system, including the tonal balance and timing cues

of the entire electronics chain. In this way, the REL is fed the exact signal that is fed to the

main speakers.

B. When possible, the REL should be placed in one of the corners behind the speakers.

Remember, we are dealing with true LOW bass pressurisation with RELs, not the mid-bass

that most competitors settle for. Low bass pressurisation below 40Hz is best derived from

corner placement, where the most linear and efficient low bass can be produced.

Basic set-up should take no more than ten to fifteen minutes to accomplish once connected.

Connecting

High-level connection, using the enclosed cable with the Neutrik Speakon connector, is

always the first choice. By connecting to the amplifier’s speaker outputs the sonic signature

of the entire amplification chain is folded into the signal for the sub, thereby keeping timing

and timbre cues consistent. In other words, the signal sent to the REL is exactly the same

signal sent to the speakers, allowing for seamless integration. This connection can be made

without affecting the performance of the amplifier because the sub’s amplifier input

impedance is 100,000 ohms. This scheme also avoids adding any detrimental effects by not

interposing any additional electronics into the amplification chain.

• The standard high level hook up procedure is: attach the red wire to the amplifier’s right

positive speaker output terminal; attach the yellow wire to the amplifier’s left positive speaker

output terminal; attach the black wire to which ever of the amplifier’s ground output terminals

is convenient; plug the Speakon connector into the sub’s high level input.

• For differential amplifiers using one sub, simply use the standard connecting scheme with the

exception of connecting ground to chassis ground, not to speaker output ground, and then

connecting into the high level input (Hi Input or Unbal Hi Input on Stentor III and Studio III).

• For differential amplifiers using two subs, one for each channel: connect red to positive;

yellow to negative; and black to chassis ground; plug the Speakon into the balanced high

level input (Bal Hi Input).

Low-level connection, RCA inputs (or XLR on some models), is always an option, should high-level

connection not be possible, or in a theatre system where both high-level and low-level connection

should be used. When connecting to the low level inputs, connect a single RCA cable to the 0dB

RCA jack. Additional gain can be achieved by connecting to the +12dB input. If you are connecting

two channels of stereo output from a pre-amplifier, simply use a high-quality y-adapter to sum the two

signals together.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rel quake Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info