Bedienungsanleitung Remeha Flexistor (Seite 3 von 36) (Englisch)

805760

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Product specication

Introduction

Congratulations on your purchase of a Remeha Flexistor unvented water heater. The Remeha

Flexistor products are manufactured in the UK from top quality materials and meets all the latest

relevant safety and constructional standards. The high grade Duplex stainless steel cylinder

o󰀨ers exceptional strength and corrosion resistance which is backed by a 30 year warranty* Its

performance and insulation levels exceed the latest requirements of Building Regulation Part L.

The Remeha Flexistor unvented water heater can be fed directly from the cold water mains

supply to the property without the need for separate feed cisterns or vent pipes. It is supplied

complete with all its necessary inlet and safety controls.

The Remeha Flexistor cylinder range all require a separate expansion vessel to accommodate

any expanded water.

General Requirements

IMPORTANT: Please read and understand this product guide before installing the Remeha

Flexistor water heater. Incorrect installation may invalidate the warranty*.

The Remeha Flexistor must be Installed, Commissioned and Maintained by a competent

installer in accordance with Building Regulation G3 (England and Wales), Technical Standard

P3 (Scotland) or Building Regulation P5 (Northern Ireland) and the Water Fitting Regulations

(England and Wales) or Water Byelaws (Scotland).

* See Terms and Conditions of warranty

THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND

PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK

OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR

INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND

THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH THE APPLIANCE.

CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT

SUPERVISION

WARNING: Do not switch on if there is a possibility that the water in the heater is frozen.

Also:

- water may drip from the discharge pipe of the pressure-relief device and this pipe must be left

open to the atmosphere; (see page 19 for more details)

-the pressure-relief device is to be operated regularly to remove lime deposits and to verify that

it is not blocked; (see page 23 for more details)

- how hot water can be drained. (see page 23 for more details)

- A discharge pipe connected to the pressure-relief device is to be installed in a continuously

downward direction and in frost free environment; (see page 20 for details)

- details on how to set the temperature controls for immersion heaters can be found on pages

10.

Note: This Remeha Flexistor cylinder needs a minimum 100L/min water supply at open outlet.

Important Notice:

When installed with the KIWA approved unvented kit Remeha Flexistore cylinders are

approved as meeting current water regulations.

To satisfy these regulations when the kit is not supplied it will be required that the installer

ensures that all of the system components meet the required standards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Flexistor Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info