Bedienungsanleitung Remeha Flexistor (Seite 13 von 36) (Englisch)

805760

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation & Commissioning

General installation

Pipe ttings

All pipe connections to the Remeha Flexistor are made via BSP female parallel threaded pipe

connection directly to the unit.

Cold water supply

A 2”cold water supply is recommended, however, if a smaller supply exists which provides

su󰀩cient ow this may be used. More ow noise may be experienced from small bore pipes due

to the increased water velocity through them. A minimum ow rate of 100l/min is required for the

Remeha Flexistor range of cylinders

High ow cold water control pack (Low and high pressure)

The control pack consists of a Pressure Reducing Valve with integral strainer, check valve, core

unit and expansion relief valve. The pressure settings are adjustable for the low or high pressure

valve sets. For the“low” pressure valve set the pressure reducing valve can be set between 1.5

and 6 bar. For the “high” pressure valve set the pressure can be set between 5 and 10 bar. For

optimum performance the following installation instructions should be complied with.

Note: The expansion vessel pressure must be set in accordance with the inlet pressure set on the

pressure reducing valve by the installer. Set the Expansion Vessel pressure before pressurising

the cylinder.

Installation

Flush supply pipe work before connection to remove all ux and debris prior to tting the inlet

controls. Failure to do this may result in irreparable damage to the controls and will invalidate the

warranty.

The pressure reducing valve can be tted in any orientation to suit the installation as long as it is

tted in the correct ow direction. Check the ow arrows on the side of the body.

The expansion relief valve should be installed with the discharge pipe work in either the horizontal

position or facing downwards, if the discharge pipe is facing upwards debris may be deposited on

the seat of the valve when in operation.

The blank plastic plugs in the body of the pressure relief valve are pressure gauge connections to

enable pressure monitoring to be carried out, should the system develop a fault. It is recommended

that these be accessible (the pressure reducing valve has two – only one need be accessible).

Expansion relief discharge pipe work must be connected to a safe visible discharge point via a

tundish and the pipe work must have a continuous fall. If site conditions allow, the expansion relief

discharge pipe work can be connected to the T&P valve discharge pipe work before the tundish.

Pressure Reducing Valve

The Pressure Reducing Valve can be connected anywhere on the cold water mains supply prior

to the Remeha Flexistor unit. There is no requirement to site it close to the unit, it can be located

at a point where the mains supply enters the premises if this is more convenient but you must

install a non-return valve just after the reducing valve for ease of maintenance. The pressure

reducing valve incorporates a adjustable pressure reducer / strainer. The valve can be tted in

any orientation to suit the installation, however, ensure that the valve is installed with the direction

of ow arrows (stamped on the side of the brass body) pointing towards the Remeha Flexistor

cylinder

PRV WARNING:

IF THERE IS AN UPSTREAM CHECK VALVE OR FITTING WHICH MAY PREVENT BACK FLOW

THEN HIGH PRESSURES CAN BE EXPERIENCED DUE TO AMBIENT TEMPERATURES

WHICH CAN CAUSE DAMAGE TO THE VALVES AND FITTINGS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Flexistor Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info