Bedienungsanleitung Remeha Flexistor (Seite 18 von 36) (Englisch)

805760

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Note: An alternative approach for sizing discharge pipes would be to follow Annex D, section

D.2 of BS 6700:2006 + A1:2009 Specication for design, installation, testing and maintenance of

services supplying water for domestic use within buildings and their curtilages.

3.59 Where a single common discharge pipe serves more than one system, it should be at least

one pipe size larger than the largest individual discharge pipe (D2) to be connected.

3.60 The discharge pipe should not be connected to a soil discharge stack unless it can be

demonstrated that the soil discharge stack is capable of safely withstanding temperatures of the

water discharged, in which case, it should:

a. contain a mechanical seal, not incorporating a water trap, which allows water into the branch

pipe without allowing foul air from the drain to be ventilated through the tundish;

b. be a separate branch pipe with no sanitary appliances connected to it;

c. if plastic pipes are used as branch pipes carrying discharge from a safety device, they should

be either polybutalene (PB) or crosslinked polyethylene (PE-X) complying with national stand-

ards such as Class S of BS 7291-2:2006 or Class S of BS 7291-3:2006 respectively; and

d. be continuously marked with a warning that no sanitary appliances should be connected to

the pipe.

Notes:

1. Plastic pipes should be joined and assembled with ttings appropriate to the circumstances

in which they are used as set out in BS EN ISO 1043-1:2002 Plastics. Symbols and abbreviated

terms. Basic polymers and their special characteristics.

2. Where pipes cannot be connected to the stack it may be possible to route a dedicated pipe

alongside or in close proximity to the discharge stack.

Termination of discharge pipe

3.61 The discharge pipe (D2) from the tundish should terminate in a safe place where there is no

risk to persons in the vicinity of the discharge.

3.62 Examples of acceptable discharge arrangements are:

a. to a trapped gully with the end of the pipe below

a xed grating and above the water seal;

b. downward discharges at low level; i.e. up to 100mm above external surfaces such as car

parks, hard standings, grassed areas etc. are acceptable providing that a wire cage or similar

guard is positioned to prevent contact, whilst maintaining visibility; and,

c. discharges at high level: e.g. into a metal hopper and metal downpipe with the end of the dis-

charge pipe clearly visible or onto a roof capable of withstanding high temperature discharges of

water and 3 m from any plastic guttering system that would collect such discharges.

3.63 The discharge would consist of high temperature water and steam. Asphalt, roong felt and

nonmetallic rainwater goods may be damaged by such discharges.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Flexistor Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info