Bedienungsanleitung Remeha Flexistor (Seite 22 von 36) (Englisch)

805760

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Commissioning

Filling and ushing the Remeha Flexistor

Ensure that all ttings and immersion heaters are correctly tted and tightened.

i) Open a hot tap furthest from the Remeha Flexistor.

ii) Open the mains stop cock to ll the unit. When water issues from the tap, allow to run for a few

minutes to thoroughly ush through any residue, dirt or swarf, then close tap.

iii) Open successive hot taps to purge any air from the system.

iv) Check all connections for leaks and rectify as necessary.

v) The Strainer housed within the Pressure Reducing Valve should be cleaned to remove

any debris that may have been ushed through the main supply pipe.

Check the operation of the Safety Valves

i) Slowly, manually open for a few seconds, the Temperature and Pressure Relief Valve

(T&P Valve) situated on the Remeha Flexistor unit. Check water discharged runs freely

away through the tundish and discharge pipe work. Close valve, ensure water ow stops

and valve reseats correctly.

ii) Repeat for the Pressure Relief Valve.

NOTE: The water discharged may be very hot.

Primary Heat source (when tted)

Connect up primary heat source as per manufacturers instructions. Fill up primary and second-

ary circuits, bleeding any air that may be trapped and check for leaks. Make sure secondary cir-

cuit has wholesome water only, the Flexistor range of cylinders do not have an internal heat ex-

changer. Take care that the Primary Heat source can handle the working pressure of the cylinder.

Auxiliary power supply (Immersion Heaters)

Switch on the electrical supply to the immersion heater(s) and allow the unit to heat up. Check

that the thermostat operates correctly. A storage temperature of approx. 60ºC is recommended,

install and set up immersions as per immersion heater tting instructions (36006161) . Check

that no water is discharged from either the Expansion Valve or Temperature and Pressure Relief

Valve during the heating cycle. The thermal cut-out is factory set to 80°C max for direct heating

Benchmarktm Log Book

On completion of the installation and commissioning procedures detailed in this Product Guide

the BenchmarkTM “Installation, Commissioning and Service Record Log” should be completed

and signed o󰀨 by the competent installer or commissioning engineer in the relevant sections. The

various system features, location of system controls, user instructions and what to do in the event

of a system failure should be explained to the customer. The customer should then countersign

the BenchmarkTM commissioning checklist to accept completion. The Service Record should be

lled in when any subsequent service or maintenance operation is carried out on the Remeha

Flexistor unit.

See pages 32 and 33 for BenchmarkTM logbook and service record

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Flexistor Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info