Bedienungsanleitung Remeha Gas 3002 ECO (Seite 28 von 36) (Englisch)

8437

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Remeha

Gas 3002 ECO

11.1 Technical data

Control box: Remeha mbc 3.0

Mains voltage: 230V - 50Hz

Minimum ionization current: 1.0 µA DC

Reaction time of flame protection: 1 sec.

Safety time: 3 sec.

Max. allowable ambient temperature: 60°C

Number of start attempts: 5

Cut-out differential pressure: 50 Pa.

The control box is sensitive to phase/neutral!

The control panel comes with an alphanumeric LCD-

display. The entire starting cycle can be followed on

this display. Using the code connector (boiler recognition

connector) the control unit automatically recognizes the

boiler type. During initial commissioning the control unit

will indicate that it recognizes the boiler type code (if

not: see para. 12). Still, it will ask you to check the type

indicated on the sticker placed on the boiler (next to the

boiler data batch, behind the front panel casing).

See also point 8, para. 11.2.

Attention:

If the boiler takes it’s combustion air from the boiler

room and is commissioned before building works are

completed on the site, particular care must be taken to

avoid dust and dirt particles from the site being drawn

into the boiler house and into the boiler during operation.

Special inlet filters are available for use on the boiler if

the need arises (please contact our technical department

for further information on their use).

11.2 Initial lighting

1. Check the gas connections.

2 Check the electrical connections, phase-neutral-earth

and all earth wires.

3. Check the water level.

4. Check the presetting of the N- and V- controllers

(see fig. 21 for 7 and 9 sections, and fig. 22 for

11 to 19 sections):

5. Switch on the circulation pump and check assembly

position and direction of rotation.

6. Switch on the power supply to the boiler.

7. Activate the main switch on the instrument panel.

11. COMMISSIONING

Fig. 18 Boiler type label

8. Only at initial commissioning:

Select the language in which the texts should appear

on the display using the ' '- and ' ' buttons

and confirm the selection with the ' ' button.

Check the boiler type. Spread over a number of me-

nus, the boiler type specifications will appear on

the display of the control unit. Compare these with

the specifications on the boiler type label (next to the

boiler data batch, behind the front casing, figure 18).

By always confirming the correctness of the specifi-

cations mentioned in a specific menu with the

' ' button, you will travel down the menus until you

get to the main menu (see para. 7.3).

9. Select the service level by travelling down the user

menus using the ' ' button. Enter code 00 12 using

the ' '- and ' ' buttons and confirm it with the

'' button.

10. Now select the option “Service tests” with the

' ' button and confirm it with the ' ' button.

The cursor now can be placed on the following

options: 1.) Boiler on?

2.) Fan on?

3.) Ignition on?

Set the cursor on "Ignition on?" and confirm with the

' '-button. The boiler will now simulate a start, with

closed gas valve. Check the ignition by looking

through the looking glas in the end sections of the

boiler. If you don't see the sparks clearly, check the

position of the ignition electrode.

Controllers Presetting

1,0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Gas 3002 ECO Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Remeha Gas 3002 ECO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info