Bedienungsanleitung Remeha Gas 310 Eco (Seite 10 von 20) (Deutsch, Englisch, Holländisch, Französisch)

627780

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Remeha

Gas 310/610 ECO

LAYOUT OF THE INSTRUMENT PANEL

fig. 03 Instrument panel

00.31H.79.00010

The Remeha Gas 310 ECO boiler is supplied with

an instrument panel. The Remeha 610 ECO is sup-

plied with an instrument panel on each boiler module.

This instrument panel is provided with an intelligent,

advanced boiler control (‘abc

’). Using the keys, differ-

ent menus can be accessed, various values can be read

and settings made. The instrument panel consists of the

following components:

1. On/off switch.

2. PC-connection.

3. Facility for incorporating a rematic

weather com-

pensator.

A. Code-display, indication of operating, setting, read-

out, shut-off, test and failure codes.

B. t-display, indication of temperatures, settings and

shut-off and lock-out codes.

C. Reset-key, to reset the boiler after a lockout.

D. m-key, key to select the required mode (mode-key).

E. s-key, key to select the required program within

the selected mode (step-key).

F. e-key, key to save the settings (store-key).

G. [+]-key, to select a higher setting.

H. [-]-key, to select a lower setting / switch function:

manual override (hand/auto).

The user has a number of setting options, which can

be evoked via the m-key. The desired code (see next

text block) can be chosen by pressing the m-key until

the digit ! (with dot) appears in the code-display. Now

choose the desired code by pressing the s-key. Next,

set the required value in the t-display, using the [+]-

and [-]-keys. Press the e-key to store the new value

(value will flash twice).

To gain access to the service level, the control system

requires an input code.

The boiler control has the following pre-set values:

! Flow temperature : 90°C

@ Pump run on time : 3 minutes

A Boiler control : 31 - modulating on flow

temperature without booster

function.

Settings should only be adjusted after consulting

your installer (or in case of emergency), see section

‘Setting mode at user level’ in our Technical Information.

Code reports in code-display

1 - only digit or letter; operating mode

! - digit or letter with dot; setting mode

! - digit or letter with flashing dot; read-out mode

b - letter b; shut-off mode (temporary, no boiler failure)

1 - digit flashes;failure mode

Operating mode (x [[)

During operation the code window shows the status

(operation) of the boiler, whereas the t window indi-

cates the measured boiler flow temperature.

Code Description

Stand-by; no heat demand

Vent (pre-ventilation time 12 seconds, post

ventilation time 3 seconds)

Ignite

The boiler is firing (flame detection)

Waiting; checking that there is sufficient air

transport using fan and air pressure differen-

tial switch (LDS)

Controls stop (burner off + post ventilation)

Run-on time, pump and fan

Shutdown mode

Gas leakage control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Gas 310 Eco Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info