Bedienungsanleitung Remeha Gas 310 Eco (Seite 11 von 20) (Deutsch, Englisch, Holländisch, Französisch)

627780

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

COMMISSIONING THE BOILER

1. First follow the guidelines that your installer supplied

for the entire installation. If not available: follow the

instructions below.

2. Check the water pressure in the installation

(min. 0.8 bar). Fill up when necessary.

3. Open the main gas cock.

4. Put the boiler control to heat demand.

5. Start the circulation pump.

6. Switch on the electrical supply to the boiler and the

on/off switch on the instrument panel.

7. The following operation course shall successively

appear on the code-display:

5 = Waiting mode; the fan runs and the boiler waits

until sufficient air transport is established (air pres-

sure switch open or closed).

1 = Pre-purging.

2 = Ignition of the gas/air mixture.

3 = The burner is firing.

The boiler now operates.

If this fails to work, switch the boiler to manual operation

(see Chapter “Operation” from the Technical Informa-

tion), set the flow temperature to the desired value and

contact your installer.

PUTTING THE BOILER OUT OF OPERATION

1. First follow the guidelines that your installer supplied

for the entire installation. If not available: follow the

instructions below.

2. Turn off the boiler control.

3. Close the main gas cock.

4. Switch off the electrical supply.

Attention! Think of the risk of freezing!

If temperatures are low, it is recommended to run the

central heating installation at a reduced temperature to

avoid freezing up.

VENTING OF THE INSTALLATION

1. Put the boiler control to heat demand.

2. Open all the radiator valves.

3. Run the installation up to about 80°C.

4. Switch off the electrical supply to the boiler.

5. Wait for approximately 10 minutes.

6. First vent the installation on all the vent points

(boiler, radiators, etc.).

7. Check the water pressure and, if necessary, fill up to

design system pressure; entirely fill the filling hose

before connecting it to the installation.

8. Put the boiler into service again.

Repeat venting procedure, if necessary.

Attention!

A poorly vented installation may cause water flow prob-

lems and air noise in the boiler, the pipework and the

radiators.

TROUBLE SHOOTING

Before calling in the installing engineer, first check if:

- The gas cock is open

- The maximum operating temperature setting is high

enough

- The boiler control has been correctly set

- The main switch is on

- A sufficient water flow is possible

(the radiator valves are entirely opened)

- The water pressure is sufficient (> 0.8 bar).

Note down the failure message before resetting

(3 digits, blinking and dots included). Reset the failure

by pressing the reset-key on the instrument panel. If the

boiler failure is immediately repeated, contact the install-

ing engineer, stating the failure message.

Attention!

Do not forget that your central heating installation needs

servicing once a year.

On gas smell: close main gas cock and warn gas com-

pany or installer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Gas 310 Eco Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info