Bedienungsanleitung Remeha Sol Plus (Seite 61 von 72) (Englisch)

805721

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

InstallationIndications, functions and optionsMessages Commissioning Operation and function

If priority PRIO 0 is adjusted and the switch-on conditions for both stores are

fullled, the stores are loaded in parallel (Arr 6) or in store sequence control (Arr

4, 5) respectively, beginning with the store with the lowest temperature. In store

sequence control, solar loading will switch from one store to the other in steps of

5 K [10 °Ra] temperature difference between the stores.

If PRIO 1 / 2 is adjusted, store sequence control will be activated (see below) with

the corresponding store as the priority store.

Note

If the priority is set to PRIO Su 1 or Su 2, solar loading of the subordi-

nate store will be stopped at once if the temperature in the priority store

(store 1 for Su 1, store 2 for Su 2) falls below the adjusted maximum tem-

perature. If, in that case, the temperature difference between the priority

store and the collector is not sufciently high, solar loading will be stopped

completely.

Spreaded loading temperature difference

(only available if PRIO is set to SE 1 or SE 2)

DTSE

Temperature difference spreaded loading

Adjustment range: 20 … 90 K [40 … 160 °Ra]

Factory setting: 40 K [70 °Ra]

Store sequence control (only available if priority is set to PRIO SE 1, SE 2, 1 or 2)

tLB

Loading break store sequence control

Adjustment range: 1 … 30 min

Factory setting: 2 min

tRUN

Circulation runtime store sequence control

Adjustment range: 1 … 30 min

Factory setting: 15 min

Store sequence control will be activated when PRIO is set to SE 1, SE 2, 1 or 2.

If the priority store cannot be loaded, the subordinate store will be checked. If use-

ful heat can be added to the subordinate store, it will be loaded for the circulation

time (tRUN – factory setting 15 min). After this, the loading process stops and the

controller monitors the increase in collector temperature during the loading break

time tLB. If it increases by 2 K [4° Ra], the break time timer starts again to allow

the collector to gain more heat. If the collector temperature does not increase suf-

ciently, the subordinate store will be loaded again for the tRUN runtime as before.

As soon as the switch-on condition of the priority store is fullled, it will be loaded.

If the switch-on condition of the priority store is not fullled, loading of the subor-

dinate store will be continued. If the priority store reaches its maximum tempera-

ture, store sequence control will not be carried out.

If store sequence control is active and the system switches to load the priority

store, the parameter tLB also acts as a stabilisation time, during which the switch-

off condition DT F is ignored while the system operation is stabilising.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Sol Plus Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Remeha Sol Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info