Bedienungsanleitung Remington Beard Kit Trimmer MB4050 (Seite 7 von 172) (Alle Sprachen)

714796

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

5. Release the suction hooks by rotating the hook upwards. Carefully pull the hook o the

surface it was xed to.

TO THIN AND TAPER THE BEARD/MOUSTACHE

• Turn the unit on.

• Place the flat top of the trimmer comb against the skin.

• Slowly slide the trimmer through the hair. Repeat from different directions as necessary.

• If hair builds up in the trimmer comb during the trimming process, switch the unit off,

pull off the comb and brush off.

DETAILING

• To create sharp lines around your beard, press the pop-up trimmer release button.

• Start with the edge of the beard/moustache line and gently lower the trimmer blade

onto your skin. Use motions towards the edge of the beard/moustache line to trim to

the desired locations in the facial area and away from beard in neck area.

TRIMMING AND STYLING LONGER BEARDS

• To take out volume from your beard or if you want to take down the length significantly,

select your desired length setting on the XL comb (please see the table for trimming

length settings). Place the flat top of the trimmer comb against the skin. Slowly slide

through the hair. Repeat from different directions as necessary.

• If hair builds up in the trimmer comb during the trimming process, switch the unit off,

pull off the comb and brush the hair off.

HOW TO BLEND/TAPER YOUR BEARD

• Tapering is when you fade the length of your beard from shorter sideburns to a longer

beard. This is how you can truly stlye your beard based on different lengths and shapes.

1. Adjust the comb to your selected grade.

2. Grade settings and the respective trimming lengths the beard kit oers can be seen in

the table. You will either need to use the short length adjustable comb or the XL

adjustable comb depending on the grade you require. If you don’t know, you can start

at a longer trimming setting and work up towards your hairline, lowering the grade

number as you go.

3. Beard hairs sit on your face much lower than at the root compared to stubble. Therefore,

use a comb to lift up the hair you want to remove and identify where the root is. This

section of hair should be located at the middle of your ear (g. 1).

• Start grading your beard here, upwards. Don’t start clipping too low or you are going to

be taking away supporting hairs lower down.

CLIPPING

1. Lift this section of hair, guide into the adjustable comb and run the clipper through. Go

over a couple of times.

2. Now it’s time to blend. Lower the grade setting on your trimmer to move onto the next

higher section of hair (eg. grade 4 to 3). Go slightly higher than previous section

working upwards (see g. 2). Again, place hair into the comb and run the clipper through.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remington Beard Kit Trimmer MB4050 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info