510301
6
Zoom out
Zoom in
Vorherige Seite
1/111
Nächste Seite
ENGLISH
3
GBDNLFEIDKSFINPSKCZ
HUN
PL
RUTRROGRSLAE
HR/
SRB
GB
CARE FOR YOUR SHAVER
To ensure long lasting performance of your shaver, clean the head assembly regularly. The easiest and
the most hygienic way to clean the shaver is by rinsing the shaving head after use with warm water.
Always keep the protective cap on the shaving head when the shaver is not in use.
AFTER EACH USE
Ensure the lady shaver is turned off.
Press the side release button to slip open the head assembly.
Blow any loose debris from the foil.
Brush or rinse the accumulated hair from the main body of the shaver, head assembly and cutter
assembly.
Leave the head assembly open to let the shaver dry completely.
NOTE:
The lady shaver is suitable for use in the bath or shower.
Do not rinse with water hotter than 70°C.
Do not completely submerge the shaver in water.
Ensure that the lady shaver is turned off and unplugged from the mains when cleaning.
Do not clean the shaving foils with the brush.
At regular interval, put a drop of sewing machine oil onto the foils and cutters head.
REPLACING YOUR FOILS AND CUTTERS
To ensure the continued highest quality performance from your shaver, we recommend that the foil and
cutter are replaced every 6 months. These can be obtained from our nearest Remington
®
Service Centre.
Signs that your foils and cutters need replacing:
Irritation: As foils get worn, you may experience skin irritation.
Pulling: As the cutters wear, your lady shaver may not feel as close and you may feel your cutter
pulling your hair.
Wear through: You may notice that the cutters have worn through the foils.
TO REPLACE THE FOIL
Ensure the lady shaver is switched off.
Press the side release button to slip open the head assembly.
Gently push the small plastic tabs at either end of the foil carrier. The foils should then easily
detach from the head assembly.
To reassemble, snap the replacement foil carrier into position.
Close the head assembly.
CAUTION
Only hold the plastic to prevent damage to the foil.
Do not press on the foil when replacing.
TO REPLACE THE CUTTERS
Ensure the shaver is switched off and open the head assembly (as above).
To remove cutter, grasp cutter between thumb and forefi nger and pull upward.
To reassemble cutter, place cutter onto oscillator tip. Gently push down clicking into position.
100648_REM_IFU_WDF4830_21L.indd GB3100648_REM_IFU_WDF4830_21L.indd GB3 30.08.10 12:4330.08.10 12:43
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Remington WDF4830C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info