587580
17
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
Error indicated by flashing code
Display Cause Required action
88 flashes Power outage for 3 minutes Switch off and switch back on
E1 flashes Communication error display controller Contact specialist dealer
E2 flashes Circulation sensor on indoor unit faulty/tripped Contact specialist dealer
E3 flashes Frost protection sensor on indoor unit faulty/tripped Contact specialist dealer
E4 flashes Vaporiser fan motor speed too low/faulty Contact specialist dealer
E5 flashes No cooling/heating output after 30 minutes. Contact specialist dealer
E6 flashes Undervoltage protection has tripped Contact specialist dealer
E7 flashes Communication error
Reprogram (see chapter
“Programming when error E7 is indicated”)
Programming when error E7 is indicated
If error 07 "Communication error"
occurs, perform the following
programming procedure:
1. Prepare to reset the unit by
removing the batteries from the
remote control.
2. Press and hold / and put
the batteries back in the remote
control.
The display will show
"00 00 00"
3. If digit I is "0", proceed to
step "5".
4. If digit I is "1", press the
Programming E7
Digit I Digit II
Digit III Digit IV Digit V Digit VI
is displayed before continuing
with the programming
procedure!
10.
Point the transmitter on the IR
remote control at the receiver
on the indoor unit and press the
"ON/OFF" button until a beep
acknowledges that the signal
has been received. The first LED
on the right side flashes.
11.
After the acknowledgement
beep has sounded, remove
the batteries from the remote
control for approx. 1 minute.
Re-insert the batteries to
complete the programming
procedure. You can now select
the desired operating mode.
"MODE" button until digit I
changes to "0".
5. Program the 1st communication
code for digits I to VI by
pressing the following buttons
several times:
ATY 261: 04 54 05
ATY 351: 04 54 05
Verify that the correct code
is displayed before continuing
with the programming
procedure! 6. Press
the"MODE" button to save the
settings.
7. If the first digit is "1", proceed
to step "9".
8. If the first digit is "0", go back
to step "1." and repeat the
programming procedure.
9. Program the 2nd
communication code for digits I
to VI by pressing the following
buttons several times:
ATY 261: 1A 00 EA
ATY 351: 1A 00 Fb
Verify that the correct code
17
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO ATY261 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO ATY261

REMKO ATY261 Zusatzinformation - Deutsch - 1 seiten

REMKO ATY261 Bedienungsanleitung - Deutsch - 28 seiten

REMKO ATY261 Bedienungsanleitung - Holländisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info