Bedienungsanleitung REMKO ATY350 (Seite 19 von 32) (Englisch)

587577

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Selection of the installation

location

The interior unit is designed for

horizontal wall installation in the

upper wall area (at least 1.75 m

from the upper edge - ﬂoor).

However, it can also be used in the

upper wall area above doors.

The exterior unit is designed

for horizontal base installation

externally. The placement location

of the unit must be horizontal,

level and ﬁrm. In addition, the unit

must be secured to prevent it from

tipping over. The exterior unit can

be set up outside as well as inside

a building. For external installation,

please observe the following

notes to protect the unit from

atmospheric conditions.

Wall openings

■ A wall opening of at least 70

mm diameter and 10 mm slope

from the inside to the outside

must be made for each interior

unit.

■ We recommend to pad the hole

inside or to cover it for example

with a PVC pipe to avoid

damage to the lines.

■ After installation, the wall

opening should be closed off on

the building side with a suitable

sealant. Do not use cement or

lime containing substances!

Installation material

The interior unit is attached with 4

screws on the building side, through

the back wall of the unit.

The exterior unit is attached with

4 screws via a wall bracket on

the wall or a ﬂoor bracket on the

ground.

Rain

For attic or roof set up, the unit

should be installed with at least

10 cm ground clearance. A ﬂoor

bracket is available as optional

equipment.

Sun

The evaporator ﬁns of the exterior

unit are the heat discharge

components in cooling operation.

Sun exposure increases the

temperatures of the ﬁns and

therefore reduces the heat

discharge for the evaporator

ﬁns. The exterior unit should be

set up on the north side of the

building, if possible. If necessary,

a shade should be installed on the

side of the building. This can be

something like a small roof.

However, the discharging warm air

ﬂow may not be affected by the

measures.

Wind

If the unit is installed in windy

areas, then it should be ensured

that the building discharged warm

air ﬂow is carried away with

the main wind direction. If this

is not possible, wind protection

should be installed on the building

site. Make sure that the wind

protection does not affect the air

supply to the unit.

20 cm

Snow

Minimum distance to snow

Wind protection

Wind

Snow

In areas with heavy snowfall, you

should install the unit on a wall.

The installation should be at least

20 cm above expected snow levels

to avoid inﬁltration of snow into

the exterior unit. A wall bracket is

available as optional equipment.

Lines in wall opening

Control line

Condensation line

Injection line

Suction line

PVC pipe

Install the exterior unit

with appropriate anchors,

depending on the type of wall.

NOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO ATY350 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO ATY350

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info