587583
16
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
Installation instructions for qualified personnel
Important notes prior to
installation
Transport the unit in its original
packaging as close as possible
to the installation location.
This helps to prevent damage
during transportation.
Check the contents of the
packaging for completeness
and check the unit for visible
transport damage. Report any
damage immediately to your
contractual partner and the
shipping company.
Lift the unit on the corners and
not on the refrigerant
or condensate connections.
The refrigerant pipes
(injection and suction line),
valves and connections must be
insulated impervious to vapour
diffusion. If necessary, also
insulate the condensate line.
Select an installation location
which allows air to flow
freely through the intake and
outlet (see section "Minimum
clearances").
Do not install the unit in the
immediate vicinity of devices
which generate intensive
thermal radiation. Installation
near sources of thermal
radiation reduces the output of
the unit.
Only open the shut-off valves
of the refrigerant pipes after
installation is complete.
Seal off open refrigerant lines
with suitable caps or adhesive
strips to prevent the infiltration
of moisture and never kink or
compress the refrigerant pipes.
Avoid unnecessary bends.
You thereby minimise loss of
pressure in the refrigerant pipes
and ensure clear return flow of
the compressor oil.
Take special precautions with
regard to the oil return if
the outdoor component is
located above the indoor unit.
See section "Oil return flow
measures".
Only use the refrigerant pipes
provided in the delivery and
only removethe protective caps
shortly before connection to the
outdoor component.
Make all electrical connections
in accordance with applicable
DIN and VDE standards.
Always attach electrical lines
properly in electrical clamps,
otherwise a fire could result.
Both units and the extension
lines are pre-filled with
refrigerant.
Suitable protective
clothing
must be worn during
installation
.
! ATTENTION
REMKO BL
16
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

remko-bl351

Suche zurücksetzen

  • Habe Stoermeldung an Geraet BL 351 IT E4
    Welche stoerung kann das sein?
    Kaeltemittelmangel? Eingereicht am 23-3-2022 14:24

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO BL351 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO BL351

REMKO BL351 Bedienungsanleitung - Deutsch - 28 seiten

REMKO BL351 Bedienungsanleitung - Deutsch - 32 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info