Bedienungsanleitung REMKO CLK50 (Seite 6 von 20) (Englisch)

587883

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Information on the Safety Device

The device is equipped with a sensor monitoring feature

and is resistant to cool down to temperatures of -20°C;

below -20°C the device switches off; when the tempera-

ture rises above this temperature, it switches on again.

When the sensor or capillary tube is damaged, or when

an excess temperature of approximately 220°C is

reached, the liquid contained in the thermostat is emp-

tied and the device switches off for safety purposes.

The device is no longer operable and must be replaced

If it is necessary to replace the STB, only the original

REMKO part may be used.

à Make sure to install and mounting the device care-

fully.

à Do not bend the capillary tubes near to solder points.

à When installing the capillary tubes, be careful not to

damage or bend them too sharply.

à The sensors may only be mounted in the mounting

brackets supplied by the manufacturer.

à The sensors must always be free from dust and dirt.

Safety Device

The device has 3 safety functions:

à Fan control (TR)

à Temperature monitor (TW)

à Safety temperature limiter (STB)

Fan control (TR)

The fan control switches the circulating air fan off and

on. The point at which the device is switched on or off is

set in the control box via the temperature control ther-

mostat “Scale 21 – 60”.

Rated value approx. 35 to 40°C.

Temperature Monitor (TW)

When the unit is in heating mode, the temperature

monitor limits both the temperature of the unit and the

air being blown out. The switching point is set via the

temperature control thermostat “Scale 34 – 110” in the

control box.

Rated value approx. 80 to 85°C.

Safety Temperature Limiter (STB)

The STB controls the temperature monitor. The switch-

ing point is fixed. The burner is prevented from being re-

started if the STB is activated.

After the cover next to the control panel is removed, the

reset button must be pressed from the outside.

After the STB has been reset, the cover must be replaced.

Before a STB reset, check the operating conditions

to ensure that the STB temperature is not ex-

ceeded again.

à The unit generally operates properly when the waste

gas pipes have been laid at an incline and assem-

bled with vertical end pipes.

à The waste gas pipes must reach at least beyond the

gutters but preferably above the top of the roof to

prevent counter pressure caused by weather condi-

tions (e.g. wind).

à All waste gas pipe components must be securely

fastened. They may not be smaller in diameter than

the waste gas connection.

à A minimum distance of 0.6 m must be maintained

from flammable objects.

à Waste gas components incl. fasteners can be pur-

chased as accessories.

Waste Gas Pipes

When the units are operated outside or in open rooms

you do not need a waste gas pipe. However, we recom-

mend using a waste gas pipe 1 m long (see example 2)

with a rain cover on top to prevent the penetration of

rainwater and dirt.

If the units are used as room heaters, it is necessary to

route the waste gases to the outside.

Make absolutely sure that counter pressure is not

created by improperly laid waste gas pipes.

Important Information.

To prevent damage to the combustion chamber caused

by moisture build-up (condensation) (see example 3),

make sure that the waste gas pipes have a properly in-

stalled condensation trap (see example 1).

When using an waste gas connection, the burner

must be adjusted accordingly.

Example 1 Example 2 Example 3

Operation with

exhaust gas pipe

extended.

Requires conden-

sation trap

Operation without

exhaust gas pipe

extended.

max. 1 meter

Inadmissible

installation.

max.1 m.

more than 1 m.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO CLK50 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO CLK50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info