Bedienungsanleitung REMKO CLK50 (Seite 10 von 20) (Englisch)

587883

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Assembling the burner flange and the burner.

1. Check the flange gasket 6 and replace it if neces-

sary.

2. Attach the burner flange to the unit housing with the

four bolts.

Pay attention to the “UP“ (UP, HAUT) label!

3. Tighten the upper bolts.

4. Turn the lower bolts but do not tighten them so that

the burner flange can still be put together.

5. Slide the flame tube of the burner into the burner

flange.

Take note of measurement X in the diagram.

6. Attach the flame tube to the flange by lifting the

burner slightly

(3° incline)

Use a hexagon socket screw key.

7. Finally, tighten the lower bolts.

8. Replace the burner cover and attach securely with

the quick release fasteners.

Burners up to size 33: X = 20 mm

Burners larger than 44: X = 30 mm

Additional maintenance information.

à Maintenance work on the burner may only be done

by authorised personnel.

à Make sure to comply with waste gas emission limits

in accordance with regulations.

à After maintenance work is complete, conduct an

electrical safety test.

Forced-air burner and power supply

1. Check whether fuel filter is dirty.

Replace dirty filters.

2. Check that all shut-off fittings in the oil supply are

open.

3. Check that there is enough fuel in the fuel container.

4. Check whether paraffin has accumulated in the

heating oil.

This can occur even at 5 °C.

5. Check oil tubes for damage.

6. Check the sensors and capillary pipes of the safety

devices for damage or dirt.

7. Check that the temperature monitor (TW) is working

properly.

8. Check the forced-air burner for any dirt in the noz-

zle, air flow plate, filters, etc.

Troubleshooting

Unit does not start:

1. Check power supply.

1~ 230 V.

2. Set operating switch to “I”.

3. Ensure that the “operation” lamp on the control

panel is illuminated.

It must indicate that the unit is in “heating” mode.

4. Check that the bridge circuit plug or the thermostat

plug has been plugged in correctly.

5. Check the room thermostat setting.

The temperature set on the room thermostat must

be higher than the room temperature.

6. Check whether the safety temperature limiter (STB)

was activated.

You must remove the protective cover next to the

control panel.

7. Before resetting the STB, it is absolutely necessary

to determine the reason it was activated and take

appropriate measures.

The following are possible reasons:

− Unit could not cool down because the power sup-

ply was interrupted.

− Temperature of air being blown out is too high be-

cause hoses are not directing air properly.

− Air intakes and outlets are blocked.

8. Check whether the “burner malfunction” control

lamp on the control panel is illuminated.

If so, release the automatic burner relay by pressing

the reset button.

9. Set operating switch to “II”

If the fan now starts running, look for the malfunc-

tion in the burner.

Prior to doing any work on the unit, unplug it from

the power supply!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO CLK50 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO CLK50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info