Bedienungsanleitung REMKO CLK70 (Seite 8 von 20) (Englisch)

587884

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1. Remove the bridge circuit plug 2.

2. Plug the thermostat plug 3 of the

room thermostat (accessories) into

the thermostat socket 1.

3. Put room thermostat 4 in a suitable

place.

The thermostat sensor may not be

placed directly in the warm air

stream or attached to a cold sur-

face.

4. Pre-select desired room tempera-

ture on the room thermostat.

5. Set the operating switch to “I”.

When heat is required, the forced-

air burner switches on automati-

cally; operation of the unit is fully-

automatic.

Fully automatic heating with room thermostat

The unit runs fully automatically with the temperature

which has been pre-selected on the room thermostat.

1 3

Hot air distribution

The units are equipped with a high-performance axial

fan. This fan has been designed to transport the hot air

directly and effectively.

It is preferable to distribute air by means of pipes or

special hot air hoses. Warm air may only be distributed

in accordance with the fan capacity of the unit in opera-

tion.

Please follow these instructions when attaching warm

air hoses:

à Use only warm air hoses (accessories) approved by

our company.

à Make sure that the hoses and/or pipes are securely

attached to the unit’s air outlet connection.

à To prevent heat from building up, the pipes and

hoses may not have sharp kinks and bends.

à Counter pressure may not be allowed to build up

when using hoses to heat closed rooms.

à If suction temperatures increase or if there is resis-

tance on the air output opening, the forced-air burner

can be switched off at short notice by the tempera-

ture monitor (TW) in heating mode.

When the temperature falls, the burner restarts auto-

matically.

à If the intervals are too short, the length of the warm

air hoses should be checked.

Avoid starting the burner in frequent cycles (under

5 min.).

Unit Shut Down

Important information about the unit’s cool-down

phase

The air supply fan continues running to cool down the

combustion chamber and then stops at a later time.

The fan can run several times before the unit is finally

switched off.

1. Set the operating switch to “0”

OFF.

2. Shut off the fuel supply.

Never interrupt (except in emergency situations)

the power supply until the cool-down phase is

completely finished.

Our guarantee does not cover damages caused to

the unit by overheating.

Maintenance and Service

Regular maintenance and observance of some basic

principles are required to ensure a long service life and

to keep the unit functioning properly.

à The unit must be maintained and cleaned at regular

intervals.

à The unit must be kept free of dust and other deposits

and may only the cleaned using a dry or damp cloth.

Do not use a direct stream of water

à Do not use any aggressive cleaning agents or those

which are harmful to the environment.

à Do not use cleaning agents which contain solvents.

à Use only clean heating oil or diesel.

Make sure to keep paraffin from accumulating.

à Check oil filters regularly and replace dirty ones.

à Check the unit for mechanical damage; replace de-

fective parts when necessary.

à Check fan blades and combustion chamber with

heat-exchanger at regular intervals and clean when

dirty.

à Check oil tanks regularly for dirt and foreign objects

and clean when necessary.

à Make sure that the waste gas and combustion air

can always be properly expelled.

à Regularly check safety devices to ensure that they

are working properly.

à Always keep safety devices free of dust and dirt.

à Have the waste gas values of the burner checked

regularly by authorized personnel.

For safety purposes, we recommend entering into a

maintenance contract!

Prior to doing any work on the unit, make sure to

unplug it from the power source!

When the temperature is too high on the unit’s

outgoing air side, the heating-operation is inter-

rupted automatically by the STB!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO CLK70 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO CLK70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info