Bedienungsanleitung REMKO GPM 15 (Seite 23 von 44) (Englisch)

587905

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

For example: Gas appliance type C:

The combustion system is tight

with respect to the environment in

which it is installed.

The combustion air is supplied

from the outside.

The units must only be operated

with suitable chimney pipes.

The components available as

accessories from the factory

comply with all requirements as

standard.

Condensation

If necessary, the chimney pipes

must be insulated to prevent the

formation of condensation in the

same.

The exhaust gas temperature at

minimum heat output corresponds

approximately to the condensation

temperature.

For pipe lengths above 5 m

indoors and 3 m outdoors,

condensation must be prevented

as follows:

■

By cladding the chimney pipes

■

By using condensate drains

from where the collected

condensation can be removed

from the chimney pipe.

Note:

Suitable condensate drains are

available as accessories.

These can be used for both

horizontal and vertical pipes.

Guide for selection

If the chimney end piece is not

connected directly to the unit,

but longer distances have to

be covered, it must be ensured

appropriate to the total length and

geometry of the chimney duct that

the end pieces and extensions as

well as the bends have the correct

diameter.

After determining the chimney

duct, the pressure loss for

the respective unit must be

determined.

The pressure loss varies for each

unit as the exhaust ﬂ ow rate is

output-dependent.

Add up the determined pressure

losses of the individual chimney

components and ensure that the

total is not above the pressure

available for the type of unit to be

used.

If a combustion air supply pipe

exists, the pressure losses must

be added to those of the chimney

pipe.

If the total pressure losses are

above the available unit pressure,

chimney and fresh air pipes with a

larger diameter must be used.

In this case, calculation must be

repeated.

The maximum possible pipe

lengths between the unit and end

piece are shown in the tables.

When using chimney bends,

it is necessary to take the

corresponding pressure losses into

account.

NOTE

Exceeding the permissible

pressure losses in the pipes

will reduce the heat output

and affect the safe operation

of the units.

ATTENTION

Installation must only be car-

ried out by authorised specia-

lists.

Pressure loss examples:

A 90° bend with Ø 80

corresponds to a 1.7 m straight

pipe length

A 45° bend with Ø 80

corresponds to a 0.8 m straight

pipe length

A 90° bend with Ø 100

corresponds to a 1.9 m straight

pipe length

A 45° bend with Ø 100

corresponds to a 0.9 m straight

pipe length

Examples of chimney pipe and

combustion air pipe arrangements

are shown on the following pages.

The units are classiﬁ ed for the

following individual installation

B23/C13/C33/C43/C53/C63

variants:

The use of plastic chimney

pipes must be avoided.

ATTENTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

REMKO GPM 15 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von REMKO GPM 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info