587906
32
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
32
REMKO GPM
7) Checking the ionisation flow
Carry out this check using a
tester that is able to measure
microamperes using DC current.
- Disconnect the unit from the
mains supply.
- Disconnect the cable from the
flame monitoring device and
connect it to the negative pole of
the tester.
- Establish a cable connection
between the positive pole of the
tester and the flame monitoring
device.
- Switch on the unit again and
measure the ionisation flow.
The ionisation flow value must be
above 2 microamperes (µA).
Lower values are a sign of a badly
positioned or oxidised electrode.
- Remove the fixing screws for
the cover [A] of the chimney
collection box.
- Using a suitable pipe brush, clean
the entire length of the pipes on
the inside, whereby the dirt must
be swept towards the collection
box as far as possible from where
it can be removed by suction.
- After cleaning the pipes, refit
the cover [A] of the chimney
collection box and check for
tightness.
- After completing the work,
reconnect the unit and carry out
a test run.
A
Regular cleaning and
maintenance at the latest after
each heating period is a basic
precondition for a long service
life and trouble-free operation
of the units.
NOTE
Adjustments and maintenance
must only be carried out by
authorised specialists.
NOTE
Due to the perfect combustion of
the units, only negligible deposits
normally accumulate here.
Nonetheless, deposits can
accumulate in the heat exchanger
tubes in the course of time. The
usual maintenance intervals must
therefore be observed in any
event.
A symptom of deposits in the heat
exchanger can be a noticeable
decrease in heat output.
The following steps must be
carried out for cleaning the heat
exchanger:
- Allow the unit to cool down and
disconnect it from the mains
supply.
- Open the side door of the unit.
8) Checking and cleaning the heat exchanger
Ionisation monitoring
electrode
Flame monitoring
device
Micro-ammeter
µA
s
s
s
We reserve the right to make changes to dimensions and design in the interest of technological advances.
32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO GPM 25 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO GPM 25

REMKO GPM 25 Bedienungsanleitung - Deutsch - 44 seiten

REMKO GPM 25 Bedienungsanleitung - Holländisch - 44 seiten

REMKO GPM 25 Bedienungsanleitung - Französisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info