587981
22
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Lift
Min.
2000 mm
Tension point
Cross beam wider than the unit width
2400 mm
Tension point
Cross beam wider
than the unit width
Wall breakthroughs
We recommend that you insu-
late the inside of the hole or use
a PVC pipe to prevent damage
to the lines.
After mounting, close off the
wall breakthrough on site with
suitable sealing compound. Do
not use materials containing
cement or lime!
Mounting materials
The unit is attached to the floor
using vibration dampers (acces-
sory). When fastening the unit to
the wall, particularly observe the
load capacity of the bracket and
the wall.
Selection of the installation
site
The unit is designed for outdoor,
horizontal, upright installation. The
installation site of the unit must
be horizontal, even, and firm. In
addition, the unit must be secured
against tipping.
The unit can be installed both
outside and inside a building.
During outdoor installation, ob-
serve the following notices regard-
ing the protection of the unit
against the effects of weathering.
Definition of the
danger zone
Only authorised and trained
personnel may have access to the
unit. If unauthorised personnel
could enter the danger zones, they
must be labelled with correspond-
ing signs / barriers, etc.
The outer danger zone sur-
rounds the unit with at least
2 m, measured from the unit
housing.
The outer danger zone can dif-
fer as a result of the setup. The
specialist company performing
the installation is responsible for
this matter.
The inner danger zone is
located inside the machine
and can be accessed only
using corresponding tools.
Unauthorised persons must not
access this danger zone!
Rain
In case of installation onto the
floor or roof, there must be a mini-
mum floor clearance of 10 cm.
In the case of units for cooling and
heating (heat pump function only),
a raised installation increases the
generated heating capacity.
REMKO KWG
22
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO KWG500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO KWG500

REMKO KWG500 Bedienungsanleitung - Deutsch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info